|
Joined: Jun 2005
Posts: 115
Member
|
OP
Member
Joined: Jun 2005
Posts: 115 |
I have set up a CCR tree and when they press 1 the call needs to be tranfered to an external number. I have it set to go to line pool 1 but the MICS say line pool A. I can see they CP grabbing an outgoing line hanging up and then giving me a message saying "the routting information configured for this call is not valid". Any suggestions would be greatly appreciated
|
|
|
Nortel Phone System Service in Canada
Do you need a Nortel Phone System technician or specific Nortel parts?
Atcom to the rescue! Our telephone techs have qualified experience servicing and troubleshooting Nortel CICS, MICS, & BCM telephone systems.
Service in Canada from sea to sea.
|
|
|
Joined: Aug 2004
Posts: 1,642 Likes: 31
Admin
|
Admin
Joined: Aug 2004
Posts: 1,642 Likes: 31 |
Make sure supervision is set up for all the lines in line pool A.
Looking for a VoIP Phone Canada provider? Put Atcom's valuable VoIP expertise to work for your business today!
|
|
|
|
Joined: Jun 2005
Posts: 115
Member
|
OP
Member
Joined: Jun 2005
Posts: 115 |
Hey Toner thanks for the reply. I do have supervision set up for all lines in pool A. The Mics is a 4.1 and the CP is a 1.5, Is it possible that this older software does not support external call transfer through CCR?
|
|
|
|
Joined: Jan 2005
Posts: 826
Member
|
Member
Joined: Jan 2005
Posts: 826 |
Hey Olympic,
The external transfer point should be supported. I would try the "route" option in place of the "pool". You will need to have a route configured that uses pool A, and a destination code the points to the route.
Good Luck!
|
|
|
|
Joined: Aug 2004
Posts: 1,642 Likes: 31
Admin
|
Admin
Joined: Aug 2004
Posts: 1,642 Likes: 31 |
The only time I've seen this symptom was on one occasion when I forgot to turn on supervision. B-guy's probably right about the destination code/route vs. line pool access code though. Do your voicemail DNs have access to the line pool?
Looking for a VoIP Phone Canada provider? Put Atcom's valuable VoIP expertise to work for your business today!
|
|
|
|
Joined: Jun 2005
Posts: 115
Member
|
OP
Member
Joined: Jun 2005
Posts: 115 |
Hey Toner yes I made sure that the Vmails DN's have access to line pool A. BCM Guy, I give the route/destenation code a try on Monday. I have set up route/dest codes for a PRI before but never for external transfer on a voicemail. Is there a certain way that this needs to be programmed?
Thanks to both of you for your reply.
|
|
|
|
Joined: Oct 2005
Posts: 4,685 Likes: 4
Member
|
Member
Joined: Oct 2005
Posts: 4,685 Likes: 4 |
Line pool has bee supported since the days of Flash voice mail.
If you're getting a routing error, be sure supervision is on for the lines in the pool and line redirect is on for the vm ports.
Marv CCNA, CTUB TeleMarv Services (Retired) Providing telecommunication solutions in Ottawa Canada since 1990
|
|
|
|
Joined: Jun 2005
Posts: 115
Member
|
OP
Member
Joined: Jun 2005
Posts: 115 |
Hi Telemarv I am on sight now and have double cheked that supervision is on and line redirect is set to Y. I have also tried to set up a rout/dest code but am still recieving the same message that routing info cofigured is not valid. These lines are analog lines and when i dial intercom 9 from a set it picks up the first available line from pool A.
Any other suggestions would be greatly appreciated.
|
|
|
|
Joined: Oct 2005
Posts: 4,685 Likes: 4
Member
|
Member
Joined: Oct 2005
Posts: 4,685 Likes: 4 |
Are you sure its pool A you are picking up and not just outdial. Check pool A access code. By default there is none, but 9 will still give you an outside line.
Marv CCNA, CTUB TeleMarv Services (Retired) Providing telecommunication solutions in Ottawa Canada since 1990
|
|
|
|
Joined: Jun 2005
Posts: 115
Member
|
OP
Member
Joined: Jun 2005
Posts: 115 |
Update... I ended up doing a re-install on the CP 100 and configured it to NVM instead of CP. Once I re-built the tree it works fine now on line pool 1.
thanks for all your help.
|
|
|
Forums84
Topics94,299
Posts638,875
Members49,770
|
Most Online5,661 May 23rd, 2018
|
|
0 members (),
140
guests, and
306
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|