|
|
Joined: Jan 2007
Posts: 18
Member
|
OP
Member
Joined: Jan 2007
Posts: 18 |
THE SYSTEM CURENTLY HAS A T-1 CARD INSTALLED AND IM NOT SURE OF THE SOFTWARE BUT THE WANT TO UPGRADE TO 7.1 RLS THEN INSTALL A PRI ENABLER AND UPGRADE TO A PRI. MY ? IS DO I NEED TO TAKE OUT THE SOFTWARE CARD ITSELF OR IS IT ALL DONE BY KEYCODES? ONE MORE THING THEY ALSO WANT A RAD INSTALLED. :confused: IS A PRI ENABLER A SOFTWARE UPGRADE OR A PHYSICAL PART?
|
|
|
Nortel Phone System Service in Canada
Do you need a Nortel Phone System technician or specific Nortel parts?
Atcom to the rescue! Our telephone techs have qualified experience servicing and troubleshooting Nortel CICS, MICS, & BCM telephone systems.
Service in Canada from sea to sea.
|
|
|
|
Joined: Aug 2003
Posts: 5,154 Likes: 2
Moderator-Vertical, Vodavi
|
|
Moderator-Vertical, Vodavi
Joined: Aug 2003
Posts: 5,154 Likes: 2 |
PRI IS ENABLED THROUGH KEYCODES. IT DOESN'T TAKE ANY MORE HARDWARE THAN THE T1.
Why are we yelling at each other?
|
|
|
|
|
Joined: Jan 2007
Posts: 18
Member
|
|
OP
Member
Joined: Jan 2007
Posts: 18 |
Thanks but what setting or heading is the pri under in the programming?{how do i get started?}
|
|
|
|
|
Joined: Jun 2005
Posts: 2,256
Member
|
|
Member
Joined: Jun 2005
Posts: 2,256 |
Originally posted by TIP & my partner RING:
Thanks but what setting or heading is the pri under in the programming?{how do i get started?} Hi Tip and likewise to your partner Ring  All jokes aside, programming a MICS for a PRI can sometimes be challenging even for a seasoned Nortel technician. Getting started is simple. Go to the software heading in programming and enter the PRI enabler code. If you this is your first Nortel PRI you may want to re-think going it alone. Going over it step by step in this forum just isn't feasible. It goes way beyond what we can do for you here. You may be able to sub the job and tag along to get the upper hand on the next one. The PRI set-up is not that difficult after you have done a few. It will be worth it for the knowledge you will gain from it. Someone may be willing to assist you off of the board. You will probably be charged a fee for this, as it will take a considerable amount of time to do a walkthrough over the phone. Goodluck :thumb:
|
|
|
|
|
Joined: Dec 2003
Posts: 2,086
Former Moderator-Nortel
|
|
Former Moderator-Nortel
Joined: Dec 2003
Posts: 2,086 |
To try to answer all your questions.
To upgrade to 7.1 - yes it is a cartridge replacement. What version are you running now. It may be wise to get the upgrade tool - it will keep your programming so you don't have to start over from scratch.
You can use the same T1 card but of course you need the keycode to enable it. I don't think you will see any PRI programming until you do.
The software upgrade is a physical change.
The T1 is just a keycode on whatever software you are running.....as long as it is 4.1 or higher.
The RAD is just a unit that connects to a digital port. Connect it instead of a phone.
Yes, as Richard says, it would be best to get a tech who has done upgrades and PRI's.
If CON is the opposite of PRO
Then what is the opposite of Progress?
|
|
|
|
|
Joined: Oct 2005
Posts: 4,685 Likes: 4
Member
|
|
Member
Joined: Oct 2005
Posts: 4,685 Likes: 4 |
Don't forget... Always upgrade software BEFORE hardware.
Marv CCNA, CTUB
TeleMarv Services (Retired)
Providing telecommunication solutions in Ottawa Canada since 1990
|
|
|
|
Forums84
Topics94,293
Posts638,827
Members49,768
| |
Most Online5,661
May 23rd, 2018
|
|
|
1 members (justbill),
107
guests, and
231
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
|
