|
Joined: Feb 2006
Posts: 598
Member
|
Member
Joined: Feb 2006
Posts: 598 |
Just another trick for nortel on the MIC's, always start on the right side? :rofl: :rofl:
Two girls later and I'm back.....lol...been gone a while but see same faces still here. Lol
|
|
|
Nortel Phone System Service in Canada
Do you need a Nortel Phone System technician or specific Nortel parts?
Atcom to the rescue! Our telephone techs have qualified experience servicing and troubleshooting Nortel CICS, MICS, & BCM telephone systems.
Service in Canada from sea to sea.
|
|
|
Joined: Nov 2003
Posts: 1,313
Member
|
OP
Member
Joined: Nov 2003
Posts: 1,313 |
will try it out on monday or tuesday....many thanks!
|
|
|
|
Joined: Nov 2003
Posts: 1,313
Member
|
OP
Member
Joined: Nov 2003
Posts: 1,313 |
nope. still didn't work. did the **startup (just to be sure), powered down. inserted 6 port fiber module, powered up, did **startup.
still can't see the 0X16 module in fiber #3 or the new nam on fiber #8.
am i doing it right or do you think i have a back fiber expansion?!
at least it booted up when i stuck the fiber expansion card in slot#2!!
|
|
|
|
Joined: Feb 2007
Posts: 2,473
Member
|
Member
Joined: Feb 2007
Posts: 2,473 |
Make sure that your fiber clicked in when you inserted. Red light inside 6 port expn or your 0 x 16 or NAM Module has to go away. If light is up your fiber is not in.
|
|
|
|
Joined: Feb 2007
Posts: 2,473
Member
|
Member
Joined: Feb 2007
Posts: 2,473 |
BDW Your Stn.Module should be shown in Hardwere automaticelly. If it isn't and you have an option to Change do it then go into Maintenence and if it shows Unequiped Disable it manually and Enable it again. Port #3 is the lowest on the 6 port expension and #8 on the top. Nortel recomendes keep #8 & #7 for the Trunk expension.
|
|
|
|
Joined: Nov 2003
Posts: 1,313
Member
|
OP
Member
Joined: Nov 2003
Posts: 1,313 |
red lights were all on in every port.
did that very thing. disabled & re-enabled. still didn't show.
i tried the nam & the 0X16 in several other ports as well.
|
|
|
|
Joined: Feb 2006
Posts: 598
Member
|
Member
Joined: Feb 2006
Posts: 598 |
And your fiber patch cables you are using are new?
Two girls later and I'm back.....lol...been gone a while but see same faces still here. Lol
|
|
|
|
Joined: May 2007
Posts: 231
Member
|
Member
Joined: May 2007
Posts: 231 |
try placeing phone on 1st new station port...think wont show until phone plugged in
|
|
|
|
Joined: Feb 2006
Posts: 598
Member
|
Member
Joined: Feb 2006
Posts: 598 |
[QUOTE]Originally posted by luv2ski: try placeing phone on 1st new station port...think wont show until phone plugged in [/QUOTE On any station port on that 0x16. Good call Ski.
As for the NAM, after you plug it in, how long are you waiting for it to come up?
Two girls later and I'm back.....lol...been gone a while but see same faces still here. Lol
|
|
|
|
Joined: Nov 2003
Posts: 1,313
Member
|
OP
Member
Joined: Nov 2003
Posts: 1,313 |
nickels>>tried different fiber cords.
luv2ski>>phone showed nothing. and i wouldn't thinkit would until the mics see's the card
nickles>>i have waited up to 20 minutes for the nam and/or the 0X16 to come up. as a matter of fact they are STILL plugged in and the system STILL doesn't see them as of today. so over 24 hours.
|
|
|
Forums84
Topics94,297
Posts638,856
Members49,769
|
Most Online5,661 May 23rd, 2018
|
|
1 members (Carl Navarro),
134
guests, and
272
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|