Phone Systems

Previous Thread
Next Thread
Print Thread
Rate Thread
Joined: Mar 2006
Posts: 187
Dalavar Offline OP
Member
OP Offline
Member
Joined: Mar 2006
Posts: 187
Anyone tried hooking up Talk-Back or Zone Paging to the EPG ports on a TDA? I couldn't get it to work at all. Had to move it to an unused CO Port, and then I had some delay issues I had to work around. This was not a problem on the TD systems.

And it didn't help that Tech Supports canned response was: "we only support Loop CO lines being attached to our CO Cards"

EMP & Lightning Home Surge Protection
EMP - Click Here!
Joined: Sep 2007
Posts: 16
Member
Offline
Member
Joined: Sep 2007
Posts: 16
I have a site with a TDA100 using zone paging. There's a detection timer in the switch that hast to be reduced to remove the delay you are experiencing. I am not sure exactly what program address it was, but I can look at the backup later if you still need help.

Jason

Joined: Mar 2006
Posts: 187
Dalavar Offline OP
Member
OP Offline
Member
Joined: Mar 2006
Posts: 187
Is the detection timer for the CO port? I have it working on the CO port and did have to change a timer. My issue is that it should work over the normal External Page Port and not have to be set up on a unused CO port.

If I have a customer that needs 8 lines I have to buy a 8 Port Loop Start Card just for one port for paging. Or start with a 16 Port Card. Which seems kinda silly since it's supposed to have 2 external page zones built in.

Joined: Jul 2006
Posts: 2,560
Likes: 1
Moderator-Panasonic
***
Online Content
Moderator-Panasonic
***
Joined: Jul 2006
Posts: 2,560
Likes: 1
Why should Panasonic or any other manufacturer provide two way transmission on a page port? Of the systems I have sold, you have very few that don't just put an amplifier on the page port and it's one way.

Now in the old Comdial days, you could make any voice port or trunk port page so it was 2-way, but it seems to me that Partner, Panasonic, Vodavi, and the like were one way paging only, ans some of them wouldn't even let you send dtmf to a Valcom zone page on the page port.

Carl


There's no place like 127.0.0.1
Joined: Jan 2007
Posts: 2,082
Likes: 1
OBT Offline
Admin
*****
Offline
Admin
*****
Joined: Jan 2007
Posts: 2,082
Likes: 1
the delay is with the inter digit muteing on co lines. I had this problem using a co line as a hot line, there is 10 second delay before mute is released on line . you can change this but it will affect all co lines and cause reorder tone to kick in quicker, if the timer is reduced. the only way i could do was set up a button with 80611 and put that line in to group 6 and that sent 2 DTMF tones on the line to get the system to release the mute as it waits for 2 digits or 10 seconds to end inter-digit timer


“I have not failed. I've just found 10,000 ways that won't work.”
Joined: Sep 2007
Posts: 4
Member
Offline
Member
Joined: Sep 2007
Posts: 4
HEY GUYS I HAVE A PANASONIC KX-TDA1232 THE SYSTEM IS WORKING THE PROBLEM IS THE INTERFACING W/C.O LINE THE LINE IS MALFUNTION EVERY DAY WEN I TRY TO FULL OUT THE LINE IN THE SYSTEM THE LINE IS HUNG BUT IN 15MIN. THE LINE IS BACK TO NORMAL........
I TRY TO ISOLATE THE SYSTEM W/ LOOP BACK IT OK THE LOCAL LINE I CONNECT IN THE C.O LINE IS NOT MALFUNTION

GIVE ME THE IDEA GUYS THANK YOU

REX :rofl:


Moderated by  Carl Navarro, OBT 

Link Copied to Clipboard
Advertising Sponsor
Most Recent 5 Post
Coaxial Cable
by dexman - 03/04/21 03:53 AM
Netlink or CCIS
by Yoda - 03/02/21 02:32 PM
SX200 ICP & ASU Bad ports
by Barrontel - 03/02/21 03:15 AM
NEC SV8100 Inmail Utility
by Sam Juniper - 03/01/21 11:02 PM
IP office and routing calling groups
by High Mesa Communications - 03/01/21 10:56 PM
Popular Topics (Views)
Forum Statistics
Forums95
Topics94,282
Posts639,048
Members49,425
Most Online5,661
May 23rd, 2018
Today's Birthdays
oldtimer1
Newest Members
Sam Juniper, B Ledford, Jonie4, James Wright, TechnoloJay
49,425 Registered Users
Get Tech Support Now! Click the banner below
Get Tech Support Now!
Top Posters (30 Days)
dexman 23
Ruben 22
pvj 11
Linked Banner to your Product or Website
EMP Shield for Commercial - Home & Vehicle
Use Coupon code SAVE - Click Here!
Who's Online Now
31 members (phonemeister, sundance, byacey, dexman, RATHER BE FISHING, justbill, hitechcomm, Mercenary Roadie, newtecky, BobRobert, hbiss, jeffmoss26, oldpoleclimber, JBean3329, Touch Tone Tommy, kjwiewall, High Mesa Communications, Coral Tech, dans, telecom guy10, Daniel, Canteleco, Ruben, Yoda, nfcphoneman, Joel J., Bob3470, Avidcomm, Professor Shadow, pvj, Biztel Cuban Okie Tech), 625 guests, and 46 robots.
Key: Admin, Global Mod, Mod
Custom Island 58
Contact Us | Telephone System Tech Support | Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers.
©Copyright Sundance Communications 1998-2021
Trusted Partners