Previous Thread
Next Thread
Print Thread
Rate Thread
#214306 11/13/08 08:36 PM
Joined: Mar 2004
Posts: 880
Likes: 1
dwflood Offline OP
Member
OP Offline
Member
Joined: Mar 2004
Posts: 880
Likes: 1
I'm adding a combo T1/PRI to an MPBE with 4 cabinets to support networking of another XTS at a new remote office. I'm told by Vodavi that only cabinets 0 and 1 will support a PRI card. Can anyone verify this is true? I really wanted to install the new PRI card in cabinet 3 (4th cabinet) as there are plenty of timeslots available.

Global Test Supply 728x90
#214307 11/13/08 11:24 PM
Joined: Jan 2008
Posts: 195
Likes: 2
Member
Offline
Member
Joined: Jan 2008
Posts: 195
Likes: 2
I generally try to keep my PRI's in one cabinet just so I don't have to use the clocking cables. As far as using cabinet 0 and 1 only, there is a diagram in the install manual that shows a PRI in cab 2 under how to run clocking cables. I think they might be concerned that clocking will not carry through the SCSI connection to cabinets 3-5.

The only restriction that I know as far as card placement in a particular cabinet is with the VIOP cards.

#214308 11/14/08 07:31 AM
Joined: Jan 2005
Posts: 15,290
Likes: 3
Moderator-Vertical, Vodavi, 1A2, Outside Wire
*****
Offline
Moderator-Vertical, Vodavi, 1A2, Outside Wire
*****
Joined: Jan 2005
Posts: 15,290
Likes: 3
Cabinets 0, 1 and 2 will support a PRI, but I've found out the hard way that cabinets 3 and above will not.


Ed Vaughn, MBSWWYPBX
#214309 11/15/08 03:58 PM
Joined: Mar 2004
Posts: 880
Likes: 1
dwflood Offline OP
Member
OP Offline
Member
Joined: Mar 2004
Posts: 880
Likes: 1
Ok, I'll put the T1/PRI combo card in shelf 2.

The documentation is confusing at best. What I have is two PRIBs in Shelf 0. One PRIB in Shelf 1 and am now adding a T1/PRI combo in Shelf 2 for networking.


The existing PRIB cards are configured as this...

Shelf 0 has two PRIB to the Telco and Shelf 1 has one PRIB to the Telco. The clock switch on all three are set to on (up). The clocking cables are connected as follows - 1st PRIB to Second PRIB. Second PRIB to Shelf 0 LMU1. Third PRIB clock cable to Shelf 1 LMU2.

Am I correct to connect Shelf 1 LMU2 clock out to Shelf 2 LMU1 clock in. Then connect the new T1/PRI combo to Shelf 2 LMU with clock switch on? off?

At the remote XTS should clock switch be on or off?

#214310 11/15/08 04:51 PM
Joined: Jan 2008
Posts: 195
Likes: 2
Member
Offline
Member
Joined: Jan 2008
Posts: 195
Likes: 2
If you are networking a site, is this additional card for a point-to-point circuit? If so, it will not require a clocking cable, main site will have clocking disabled on the card, remote site will have it enabled.

#214311 11/15/08 05:06 PM
Joined: Mar 2004
Posts: 880
Likes: 1
dwflood Offline OP
Member
OP Offline
Member
Joined: Mar 2004
Posts: 880
Likes: 1
Yes, Telco has provided a point-to-point T1 between the buildings.

So, do you recommend I leave the clock switch off and omit the clock cable on the new T1/PRI combo card in the 'hub' and just enable the clock switch on the remote T1/PRI combo card?

#214312 11/15/08 05:29 PM
Joined: Jan 2008
Posts: 195
Likes: 2
Member
Offline
Member
Joined: Jan 2008
Posts: 195
Likes: 2
Point-to-point circuits never need a clock cable, this is per manual and Vodavi.

When you network sites, the hub card always has the clocking switch off, the remote site card will always be on. The only exception is when a remote site has a PRI and the main site does not, then the switches would be reversed.

Just curious, how far apart are the buildings? Do they have a data network between them? Also, will they be having a lot of calls between the buildings? You will max out at 23 calls simultaneous between facilities.

#214313 11/16/08 06:38 AM
Joined: Mar 2004
Posts: 880
Likes: 1
dwflood Offline OP
Member
OP Offline
Member
Joined: Mar 2004
Posts: 880
Likes: 1
Buildings are few miles apart. Separate p-to-p T1 for data. 23 channels should be ok. Only other trunks in remote switch are POTS.

#214314 11/16/08 02:21 PM
Joined: Jan 2008
Posts: 195
Likes: 2
Member
Offline
Member
Joined: Jan 2008
Posts: 195
Likes: 2
Great, you should be good to go then. Being only a few miles, the monthly cost for an additional T1 is pretty minimal, otherwise VOIP between sites would have been a good option too.

#214315 11/16/08 02:21 PM
Joined: Jan 2008
Posts: 195
Likes: 2
Member
Offline
Member
Joined: Jan 2008
Posts: 195
Likes: 2
.


Moderated by  EV607797, JWRacedog, MnDave, nfcphoneman 

Link Copied to Clipboard
Advertising Sponsor
Most Recent 5 Post
Saying good by to all the rest of my toshiba
by SSPhone - 05/07/21 04:28 PM
IP Office 500 V2 crash
by Mercenary Roadie - 05/07/21 08:24 AM
Random characters on screen
by dougster - 05/06/21 06:49 PM
How to subscribe to get full access.
by Ruben - 05/05/21 09:29 PM
OS UNI Card Version Question
by RM SYSTEMS - 05/04/21 04:53 PM
Popular Topics (Views)
Forum Statistics
Forums93
Topics94,377
Posts639,660
Members49,454
Most Online5,661
May 23rd, 2018
Today's Birthdays
KWH, PulseDial
Newest Members
Andrea Sau, eos90066, Sonic, ERA, Mackino
49,454 Registered Users
Get Tech Support Now! Click the banner below
Get Tech Support Now!
defencebyte.com
Antiransomware
Global Test Supply
EMP & Lightning Home Surge Protection
EMP - Click Here!
Top Posters (30 Days)
dexman 48
pvj 18
Ruben 15
bditech 11
Phone.com 300x250
300x250 Your Business Phone Service in the Cloud
www.aweber.com
landing page builder
Linked Banner to your Product or Website
NordVPN
Advertising Sponsor Spot 2
EMP Shield for Commercial - Home & Vehicle
Use Coupon code SAVE - Click Here!
Who's Online Now
30 members (sundance, nortelvoip, BobRobert, dexman, pvj, Yoda, Mercenary Roadie, CyberLaw, jeffmoss26, nameless, JBean3329, Touch Tone Tommy, Curlycord, Bushmills, Carl Navarro, Professor Shadow, SSPhone, KRRath, Ruben, justbill, gelehu, dougster, Biztel Cuban Okie Tech, hitechcomm, mongo5150, www.telcom1.net, Skunky, MooreTel, metelcom, RonP), 458 guests, and 83 robots.
Key: Admin, Global Mod, Mod
vpnproxymaster
Contact Us | Telephone System Tech Support | Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers.
©Copyright Sundance Communications 1998-2021
Trusted Partners
landing page builder Antiransomware 300x250 Your Business Phone Service in the Cloud