|
Joined: Oct 2008
Posts: 19
Member
|
Member
Joined: Oct 2008
Posts: 19 |
Do any of you guys have the part number for the Caller ID box that could be interaced with the TRIADs system? Do you remember how many lines each unit picked up? Thanks for any information.
|
|
|
Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.
|
|
|
Joined: Jan 2005
Posts: 15,404 Likes: 18
Moderator-Vertical, Vodavi, 1A2, Outside Wire
|
Moderator-Vertical, Vodavi, 1A2, Outside Wire
Joined: Jan 2005
Posts: 15,404 Likes: 18 |
1480-00 was the original unit that supported eight lines.
7480-00 was the new unit that supported nine lines.
Both are manufacturer discontinued, so used/refurbished is going to be your best bet.
Ed Vaughn, MBSWWYPBX
|
|
|
|
Joined: Oct 2008
Posts: 19
Member
|
Member
Joined: Oct 2008
Posts: 19 |
|
|
|
|
Joined: Nov 2009
Posts: 2
Member
|
Member
Joined: Nov 2009
Posts: 2 |
We have the Vodavi Triad Starplus and just got Caller ID through Verizon. I am able to do the Flash 56 and set the number and name to "yes"...but I think I am missing some software for the system. Is that correct? Is it all obsolete? Where can I purchase the software or can I tell if it is already installed? We have owned and been using the system for quite a few years, but have never had Caller ID on it before. I appreciate any help.
|
|
|
|
Joined: Oct 2001
Posts: 6,160
Member
|
Member
Joined: Oct 2001
Posts: 6,160 |
Shirl, Welcome to the board. You will need one of the caller ID units referenced in the above post.
In the future you should start a new thread rather then tacking on to an existing one, but this is so close to the original question it's ok.
|
|
|
|
Joined: Jan 2005
Posts: 15,404 Likes: 18
Moderator-Vertical, Vodavi, 1A2, Outside Wire
|
Moderator-Vertical, Vodavi, 1A2, Outside Wire
Joined: Jan 2005
Posts: 15,404 Likes: 18 |
Shirl:
You'll need one of the caller ID interface units indicated above. In addition, with the Triad-S you will need to see if your KSU has the optional serial port card installed in the bottom slot. If it is not present, you'll need one of those too.
After you have these, you'll need to make sure that the baud rate of the CID unit matches the baud rate of the serial port you are using. Lastly, you'll need to program that port to provide CID service under flash 56.
Since this system has not been manufactured in many years, you'll likely only find these items used or refurbished. Check at the top of this page to see if Sundance (our host) has them available.
Ed Vaughn, MBSWWYPBX
|
|
|
|
Joined: Jan 2008
Posts: 3,821
Retired Moderator
|
Retired Moderator
Joined: Jan 2008
Posts: 3,821 |
I am installing one today on an S and having a bit of trouble to get it to work. Programming is correct but nothing coming out of the 7480 and showing on the phone displays. I hope it isn't a bad unit.
www.myrandomviews "Old phone guys never die, they just get locked in some closet with an old phone system and forgotten about" Retired, taking photographs and hoping to fly one of my many kites.
|
|
|
|
Joined: Jan 2005
Posts: 15,404 Likes: 18
Moderator-Vertical, Vodavi, 1A2, Outside Wire
|
Moderator-Vertical, Vodavi, 1A2, Outside Wire
Joined: Jan 2005
Posts: 15,404 Likes: 18 |
Even though they said that this wasn't necessary with the 7480 units, I'm pretty sure that if pins 7 & 8 need to be shorted in order for CID data to be output.
I never tried to use the supplied ribbon cable with the 7480 for this reason. I just made my own cable and placed a jumper on 7/8 at the CID unit end.
Ed Vaughn, MBSWWYPBX
|
|
|
|
Joined: Nov 2009
Posts: 2
Member
|
Member
Joined: Nov 2009
Posts: 2 |
Wow, thanks for all of the information. Seems like this phone system is pretty complicated, but I will keep trying to get the Caller ID functional. Much appreciated!!
|
|
|
|
Joined: Jan 2008
Posts: 3,821
Retired Moderator
|
Retired Moderator
Joined: Jan 2008
Posts: 3,821 |
I have used the supplied cable before with XTSs. I would think that the S works the same way. Also according to the 7480 manual, pins 7 and 8 are shorted internally in the CID.
www.myrandomviews "Old phone guys never die, they just get locked in some closet with an old phone system and forgotten about" Retired, taking photographs and hoping to fly one of my many kites.
|
|
|
Forums84
Topics94,532
Posts640,043
Members49,853
|
Most Online5,661 May 23rd, 2018
|
|
2 members (justbill, BobRobert),
149
guests, and
28
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|