Business Phone Systems

Previous Thread
Next Thread
Print Thread
Rate Thread
#217889 04/15/10 05:46 AM
Joined: Mar 2009
Posts: 183
draynor Offline OP
Member
OP Offline
Member
Joined: Mar 2009
Posts: 183
I have a customer that is switching to DID lines. Deltacom is going to be the provider. The only info I am able to get at this time is "IP Complete PRI are being provisioned out of the Birmingham CS2K Switch due to monitoring". Does anyone have any info about this switch & Deltacom. My customer only has 6 lines & in my opinion it's kinda expensive for him to change to DID. Any info would be greatly appreciated.

Thanks David

Atcom VoIP Demo
VoIP Demo
#217890 04/15/10 08:48 AM
Joined: Jan 2006
Posts: 2,266
Likes: 1
Member
*****
Offline
Member
*****
Joined: Jan 2006
Posts: 2,266
Likes: 1
We do PRI's with Deltacom all the time , they always call us to verify the digits sent and if it needs to be NI2.

#217891 04/16/10 09:04 PM
Joined: Mar 2009
Posts: 183
draynor Offline OP
Member
OP Offline
Member
Joined: Mar 2009
Posts: 183
I take it that they do not use soft switches. Are their any quirks or anything special I need to know. This will be my first DID install. Any info would be greatly appreciated.

Thanks David

#217892 04/16/10 09:13 PM
Joined: Aug 2009
Posts: 432
Member
Offline
Member
Joined: Aug 2009
Posts: 432
David

I was about to do a PRI myself one time and was told by several Vertical Dealers and Techs to MAKE SURE you use a Hard Switch. They said the programming is easier and more secure.

#217893 04/16/10 09:34 PM
Joined: Jan 2005
Posts: 15,351
Likes: 12
Moderator-Vertical, Vodavi, 1A2, Outside Wire
*****
Offline
Moderator-Vertical, Vodavi, 1A2, Outside Wire
*****
Joined: Jan 2005
Posts: 15,351
Likes: 12
NI2 is the most common setup mistake I've encountered. The XTS won't allow you to change this setting to NI1, but for some reason, Verizon often sets up PRI circuits this way. If all outgoing calls are rejected after the cut, that is likely your problem. I can't speak for Deltacom's procedures though.

Don't forget to ask how many channels on the integrated PRI are for voice use and how many are used for data. You'll need to place the CO ports (PRI channels) used for data into trunk group zero or you won't be able to place outgoing calls.

True, a customer with only six lines might seem to be a case of overkill with a PRI, but the unused channels are usually combined to provide more data bandwidth, so the customer will be happy.


Ed Vaughn, MBSWWYPBX
#217894 04/18/10 07:49 PM
Joined: Mar 2009
Posts: 183
draynor Offline OP
Member
OP Offline
Member
Joined: Mar 2009
Posts: 183
My customer has a STSe, going to have 6 DID lines, & has 10 phones in all. So thats what I got to work with.

David

#217895 04/20/10 05:21 AM
Joined: Aug 2009
Posts: 432
Member
Offline
Member
Joined: Aug 2009
Posts: 432
David

Make sure your PRI is set up as B8ZS-ESF, NI2.
You will need the card and a PLLU. Program the card in F24 , set the trunks as TIE-DNIS under F40, B8ZS-ESF under F41, routing number under F43.


Moderated by  EV607797, JWRacedog, MnDave, nfcphoneman 

Link Copied to Clipboard
Forum Statistics
Forums84
Topics93,879
Posts637,000
Members49,673
Most Online5,661
May 23rd, 2018
Popular Topics(Views)
Today's Birthdays
cindysue, esibole1, jpblock82
Newest Members
APInc, m1cashman, jonnycom, XJR9000, BitBang
49,673 Registered Users
Top Posters(30 Days)
Toner 11
teleco 6
dexman 5
jsaad 5
tim10 4
Shahza 4
Who's Online Now
2 members (mitel_icp_tech, Gary S.), 43 guests, and 18 robots.
Key: Admin, Global Mod, Mod
Contact Us | Sponsored by Atcom: Business Phone Systems | Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers.
©Copyright Sundance Communications 1998-2023
Powered by UBB.threads™ PHP Forum Software 7.7.5