sundance-communications.com/forum Forums Other TDM Phone Systems VoiceMail Systems and Programming KeyVoice

Nick52
Installer
Posts: 28
From: Jackson, MI, 49202
Registered: Aug 2003
posted October 07, 2004 10:47
--------------------------------------------------------------------------------
I am having an issue with a comdial dx-80 voiemail. I have a dx-80 with C28 firmware. There voice mail (7270C) was smoked by some kind of power surge or whatever. So I purchased a new voicemail for them (7270-k777) I installed it and everything seemed to work fine except for some kind of timing issue. When the extension is busy on the phone I have the phones set up to call fwd busy to their voice mail boxes. What happens is that when a caller gets that extensions when it is busy through the voice mail it goes right into their mailbox and you will miss the first few seconds of the greeting.
The greeting is recorded as "Hi you've reached so and so I'm not available please leave a message and I will get back with you as soon as possible."

You hear "not available please leavea message and I will get back with you as soon as possible."

Any idea's on what to change. I looked in the manual for timing issues and I didn't see anything for a busy fwd timer. Or some kind of delay. I have even had them try to record the greeting with like a 3-4 second pause in the beginning and it did the same thing. any and all suggestions are welcome.

IP: Logged

markk
Moderator
Posts: 513
From: Gap, Pa. USA
Registered: Oct 2001
posted October 07, 2004 12:14
--------------------------------------------------------------------------------
This happens to every mailbox?
Did you watch the call progress on Keylink while testing this?
I've seen them "clip" slightly and a pause at the beginning has always solved that, but I've not seen it this bad.
mark

IP: Logged

Nick52
Installer
Posts: 28
From: Jackson, MI, 49202
Registered: Aug 2003
posted October 27, 2004 08:05
--------------------------------------------------------------------------------

quote:
--------------------------------------------------------------------------------
Originally posted by markk:
This happens to every mailbox?
Did you watch the call progress on Keylink while testing this?
I've seen them "clip" slightly and a pause at the beginning has always solved that, but I've not seen it this bad.
mark
--------------------------------------------------------------------------------

I watched the progress with keylink. Everything seems to be fine. The voicemail answers and then you dial the digits and it receives the digits. Then it transfers the call. then it plays their greeting when the extension is busy. The problem is with every mailbox not just one. I have tried to pause in the greeting personally. Sometimes the customer says they pause for 5 seconds and it is like 2. So I re-recorded the message and paused as long as I could and it won't let me pause for more than 2-3 seconds. So I muted the phone when I was leaving the message and it still won't let me pause for more than 2-3sec. I tried putting pauses in the transfer times in the VoiceMail options, still the problem persists. I have switched out the backplane and the cpm boards thinking those may be having issues. Nothing seems to work. Is there anything I am missing to check. Or can anyone think of anything to do. I am thinking that the Voice Mail Board is bad possibly. But I don't want to say that because it is brand new! Any ideas are appreciated.

Are you using blind transfer on the Keyvoice?

No, the transfer is set to "Wait for Ring"

Have you called Comdial Tech Support yet on this? I'm stumped, but it must be an issue in the VM, I can't think of anyway the phone system database could cause this.
mark

I haven't called tech support yet. I haven't had time to wait on hold that long. I am so busy doing other work. I haven't had time to just sit down and try to work this out with people. I will have time in a week or two. I was hoping somebody has had this happen to them before and I would they would be able to help me. Wishful thinking on my part.

It's a strange problem, but not all the wizards have checked in on it yet. I'll be interested to hear the solution, don't forget to post it when you figure it out.
mark

I had that problem on a keylink before, we changed the transfer to Blind. That fixed it. I don't know if it'll work for you but it couldn't hurt to try.

it is the "wait for ring" parameter. Set it to blind and that should take care of it. The "wait for ring" was designed for those systems which didn't have full vm intergration and a couple of the built in ACD and wait in line functions.

It almost seems that included in the transfer somehow is also a digit that Fast Forwards through the greeting.

Does this seem like a reasonable solution.

I think the fast forward is for about 3 to 5 seconds, so that would put you right about were your greeting picks up. I am not sure how it is doing it but this might be a start.

good luck,

2wire

I was under the impression that the Wait for Ring option was a supervised transfer mode. If it is a blind transfer the customer will not be able to go back to another extension. Or am I thining about this wrong. If I am please let me know, I don't want to be mis informed. I changed the transfer to Blind but the customer I believe is on vacation this week and has not returned my phone calls. Thanks for all of the help.