|
Joined: May 2004
Posts: 1
Member
|
Member
Joined: May 2004
Posts: 1 |
I have a at&t spirit phone system in my shop and the other day the touch pad Quit working and now it just like a rotary phonePlease help.I have a controller system# CS308A1. Contact David Tribble 770926-5883 Thanks
|
|
|
Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.
|
|
|
Joined: Mar 2001
Posts: 7,350
RIP Admin
|
RIP Admin
Joined: Mar 2001
Posts: 7,350 |
Is it a 616 or 1224? You will need to go into Admin and look at the Dial Type for the lines.
Russ runs a local service and private tech center. ![[Linked Image from sundance-communications.com]](https://www.sundance-communications.com/installers/logos/65graphic.jpg) [/url]
|
|
|
|
Joined: Jun 2001
Posts: 10,631
RIP Admin-Founder
|
RIP Admin-Founder
Joined: Jun 2001
Posts: 10,631 |
>>I have a controller system# CS308A1. Thats a 308 controller dtmf
SPIRIT CS administration may be carried out from either a 6-button or a 24-button set. Three important steps are required for entering the administration mode: 1.The control unit ADMIN switch must be ON.
2.The administration overlay must be in place on station 10.
3.The set must be plugged into control unit jack 10 (call processing is interrupted only at station 10).
DIAL TYPE Press FEATURE. Dial 7. Each line indicator light will show the current dialing type for that line. If the light is OFF, that line is set for touch tone dialing. If the light is ON, the line is set for dial pulse dialing. To change the dialing type for a line or lines, press the line button(s) and dial the appropriate digit from the table below. YOU may press more than one line button to make the change on more than one line. If you enter a digit without first pressing a line button you will hear the error tone. DIAL INDICATOR LIGHT SETTING 1 OFF Touch Tone 2 ON Dial Pulse (installed)
added: You now have it in pulse what you want is tone. If I read your post correct. let us know if it works?
[This message has been edited by test-ok (edited May 18, 2004).]
|
|
|
|
Joined: Jun 2001
Posts: 10,631
RIP Admin-Founder
|
RIP Admin-Founder
Joined: Jun 2001
Posts: 10,631 |
oh and then turn the admin switch back off. ![[Linked Image from sundance-communications.com]](https://www.sundance-communications.com/forum/smile.gif)
|
|
|
|
Joined: Mar 2001
Posts: 7,350
RIP Admin
|
RIP Admin
Joined: Mar 2001
Posts: 7,350 |
Duh, I guess if I would have looked at the # I would have figured that out.
Russ runs a local service and private tech center. ![[Linked Image from sundance-communications.com]](https://www.sundance-communications.com/installers/logos/65graphic.jpg) [/url]
|
|
|
|
Joined: May 2003
Posts: 1,362
Member
|
Member
Joined: May 2003
Posts: 1,362 |
You may need a couple more steps after moving the admin switch, and before dialing Ftr 7
1.From station 10 press intercom 2.Press speaker 3.Dial *0 4.Dial 1 5.Then Press Ftr 7
****Step 4. is where you need to be careful if you enter a "0" there instead of a "1", it will default the system if it is not defaulted already.
[This message has been edited by JOHNYREB (edited May 18, 2004).]
|
|
|
|
Joined: Mar 2001
Posts: 7,350
RIP Admin
|
RIP Admin
Joined: Mar 2001
Posts: 7,350 |
Sounds like it already defaulted bieng that it went back to pulse. I can fax you the Program page and the overlay if you would like, they are not hard to program at all.
[This message has been edited by dtmf (edited May 18, 2004).]
Russ runs a local service and private tech center. ![[Linked Image from sundance-communications.com]](https://www.sundance-communications.com/installers/logos/65graphic.jpg) [/url]
|
|
|
|
Joined: Jun 2001
Posts: 10,631
RIP Admin-Founder
|
RIP Admin-Founder
Joined: Jun 2001
Posts: 10,631 |
you can also call that dtmf and he can explain it too. click on his profiles (the little man with a ? mark) ![[Linked Image from sundance-communications.com]](https://www.sundance-communications.com/forum/smile.gif)
|
|
|
|
Joined: Jul 2008
Posts: 63
Member
|
Member
Joined: Jul 2008
Posts: 63 |
I had to switch out a spirit KSU its a 308 with a 308 expansion, all works fine but it pulse dials not tone. I slide the admin switch to admin then hit the intercom then speaker then *0 hear 2/3 beeps then hit feature and got error tone, hit 7 got error tone try hitting line 1 and error slide the admin switch back and still pulse dials help what did I do wrong Neil
|
|
|
|
Joined: Aug 2004
Posts: 9,172 Likes: 22
Admin
|
Admin
Joined: Aug 2004
Posts: 9,172 Likes: 22 |
Probably tagging on to a 10 year old thread for starters.  Best to start a new topic as many don't follow old threads plus it helps with search results.
|
|
|
Forums84
Topics94,524
Posts640,007
Members49,852
|
Most Online5,661 May 23rd, 2018
|
|
0 members (),
236
guests, and
50
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|