web statisticsweb stats Business Phone Systems Tech Talk Forum - VOIP & Cloud Phone Help

Business Phone Systems

Previous Thread
Next Thread
Print Thread
Rate Thread
#37308 08/11/07 12:59 AM
Joined: Jun 2006
Posts: 292
rage Offline OP
Member
OP Offline
Member
Joined: Jun 2006
Posts: 292
FXT 15C w/ 8.5 Keyvoice. FXT1-24 with 8 active channels.

Replaced the voicemail about 6 months ago after the original died. No problems on it or the system after until about a week ago.

Now, about once a week, all lines go out (no dial tone, no incoming calls, busy signal given). The receptionist then picks up line 1 (no dialtone) and hangs up. Line 1 now works and calls can come in. This happens on all lines.

Other wierdness, 1 extension when transfer to her and forwarded to vmail when she doesn't answer, will randomly get routed to the operator mailbox rather than her personal. This does not happen all the time, or with any other extension.

The line issues point me towards the t1 card, but no tsure on the voicemail issue. I have checked all the mbox options and they look fine. Have also deleted and readded the mbox. Also ran scandb from DOS.

Any other ideas on this one? Thanks. It may be time to upgrade them to the MP5000.

Atcom VoIP Phones
VoIP Demo

Best VoIP Phones Canada


Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.

#37309 08/11/07 06:00 AM
Joined: Jan 2002
Posts: 2,328
Moderator-Comdial
*****
Offline
Moderator-Comdial
*****
Joined: Jan 2002
Posts: 2,328
Is the system resetting? Recently had a similar issue with an fx2 in a very busy Dr office. 1 LSboard, 3digital and 1analog. System would lock up. It ended up being a digital station board and it took ten minutes to fail. When the system reset all was good and it reset on its own!

#37310 08/12/07 08:23 AM
Joined: Jun 2006
Posts: 292
rage Offline OP
Member
OP Offline
Member
Joined: Jun 2006
Posts: 292
no, not resetting. Though if I do a software reset through VMMI it returns to normal for a couple of days.

This one has (1) FXT1-24, (1)LSD (1)IST

#37311 08/12/07 12:44 PM
Joined: Jun 2004
Posts: 4,552
Moderator-Comdial, ESI, Voicemail, Cisco
Offline
Moderator-Comdial, ESI, Voicemail, Cisco
Joined: Jun 2004
Posts: 4,552
Just a shot in the dark...Did you previously have the IMOK hack implemented, and with the reinstall it didn't get reimplemented? That's in regards to the voicemail routing problem.

In regards to the "lines going down" issue, have you checked the logs on the FXT? Do you have any alarms being logged on the T1 or system?

#37312 08/14/07 07:55 AM
Joined: Jun 2006
Posts: 292
rage Offline OP
Member
OP Offline
Member
Joined: Jun 2006
Posts: 292
Not sure how to see the logs in the system itself frown

However, there are no error lights on the board, nor is it losing synch. now it has happened 3 times today. I have also called the carrier and they show no problems. When this happens it disconnects the calls as well if there are any in progress.

#37313 08/14/07 08:39 AM
Joined: Aug 2004
Posts: 9,155
Likes: 16
Admin
*****
Offline
Admin
*****
Joined: Aug 2004
Posts: 9,155
Likes: 16
Hyper term session. Printouts, system,status logs. I'd buuton map all lines ona phone at the reception desk and look for all red LEDs when the problem happens and compare that to the status logs.


[Linked Image]
#37314 08/14/07 09:16 AM
Joined: Jun 2006
Posts: 292
rage Offline OP
Member
OP Offline
Member
Joined: Jun 2006
Posts: 292
Yeah, we have the recept phone with all lines. They do not go all red. Just get no dial tone/busy until one is picked up and they hang up. Then it is fine again.

Will be on-site tomorow and will printout the logs. Figured I'd upgrade them to an MP5 but Comdial has no idea when the next training is but they want me to buy the demo ASAP. Yeah right, not until I know a training date.

#37315 08/15/07 04:44 AM
Joined: Jun 2006
Posts: 292
rage Offline OP
Member
OP Offline
Member
Joined: Jun 2006
Posts: 292
ok.....nothing on status logs. Either T1 or system that corresponds to the failures. Not even on the same day.

Also notice that one line is giving dial-tone, but when you dial a number rather than connecting it gives back dial-tone (still displays number in display though).

Also, no lights on the t1 card, no synch, no nothing. The status light is blinking though witht the rest of the cards. (maybe the led's are burnt out?)

#37316 08/15/07 05:20 AM
Joined: Jun 2004
Posts: 4,552
Moderator-Comdial, ESI, Voicemail, Cisco
Offline
Moderator-Comdial, ESI, Voicemail, Cisco
Joined: Jun 2004
Posts: 4,552
Bad T1 card? Services board? I've got both (also cabinet, sync, etc.) on the shelf, if you need either.

I'm checking with my office regarding the PM you sent me. I'll get back with you later today.

Justin

#37317 08/15/07 05:41 AM
Joined: Jun 2006
Posts: 292
rage Offline OP
Member
OP Offline
Member
Joined: Jun 2006
Posts: 292
Thanks Justin.... Just got the signoff on new mp5 from customer.


Link Copied to Clipboard
Forum Statistics
Forums84
Topics94,262
Posts638,697
Members49,757
Most Online5,661
May 23rd, 2018
Popular Topics(Views)
211,098 Shoretel
187,712 CTX100 install
186,796 1a2 system
Newest Members
BPopilek, Rich F, LewisR, TDKs79, Buttinset
49,757 Registered Users
Top Posters(30 Days)
dexman 18
Toner 11
TDKs79 8
jc2it 4
teleco 4
Who's Online Now
1 members (Toner), 116 guests, and 244 robots.
Key: Admin, Global Mod, Mod
Contact Us | Sponsored by Atcom: One of the best VoIP Phone Canada Suppliers for your business telephone system!| Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers. Sundance Phone System Forums - VOIP & Cloud Phone Help
©Copyright Sundance Communications 1998-2024
Powered by UBB.threads™ PHP Forum Software 7.7.5