Phone Systems

Previous Thread
Next Thread
Print Thread
Rate Thread
SVMI-4 Wont interface in Compact DCS
#440299 09/18/11 05:39 AM
Joined: May 2001
Posts: 175
fldiver Offline OP
Member
OP Offline
Member
Joined: May 2001
Posts: 175
Hello?
Does anyone know why when I plug a Known good SVMI-4 card in expansion slot in a Compact DCS it does not show up in MMC207? Whats the trick please help Im going back in the morning hopefully with an answer.

Thanks
FLdiver

Samsung Telephones and Equipment
Re: SVMI-4 Wont interface in Compact DCS
#440300 09/18/11 06:30 AM
Joined: Apr 2007
Posts: 544
Member
Offline
Member
Joined: Apr 2007
Posts: 544
Are you replacing the card or upgrading the system? Did do a slot pre-install in MMC 8XX?

Re: SVMI-4 Wont interface in Compact DCS
#440301 09/18/11 06:59 AM
Joined: May 2001
Posts: 175
fldiver Offline OP
Member
OP Offline
Member
Joined: May 2001
Posts: 175
The following is my previous post and no I did not do a slot pre-install...please explain further.

Hello gentlemen I am trying to install a SVMI-4 card in a Prostar DCS Compact. I have installed the VM board in expansion slot 3. The card comes up in as far as I am able to access it via hyper terminal however the status of the ports go to "starting" and it does not change. I have 2 cabinets the existing cabinet and the cabinet that my customer bought with the VM card installed in it. In the cabinet that the card came in the VM works I can call in and get messages so Im certain the card is good both systems have the same rom version. I notice in program 207 in the cabinet that works it comes up with 209 VMAA Port and that makes sense as the card was in the 1st expansion slot in the system it came in in the system Im trying to get the card to work in it says SLI NOT EXIST. Please get back any help greatly appreciated.

Thanks
FLdiver

Re: SVMI-4 Wont interface in Compact DCS
#440302 09/18/11 07:31 AM
Joined: Sep 2004
Posts: 395
Member
Offline
Member
Joined: Sep 2004
Posts: 395
What version of software and was a card ever installed in the slot that you put the SVMi card into? The old DCS systems didn't like to have different cards swapped into previously used slots. The technique I always used to clear a previously used slot was to turn cabinet off, remove old card, turn cabinet back on, do a preinstall on that slot, turn cabinet off and on again without installing a card, do another preinstall on that slot, turn the cabinet off, slide the new card in and reboot. I also seem to remember that this wouldn't work untill I put the old card back in and made sure I started the process from the beginning correctly. Last resort would be to default the cabinet and start clean. That is sometimes better.

Re: SVMI-4 Wont interface in Compact DCS
#440303 09/18/11 08:36 AM
Joined: May 2001
Posts: 175
fldiver Offline OP
Member
OP Offline
Member
Joined: May 2001
Posts: 175
Ok I did not do the preslot install and I see it now in the book. both cabinets have same software and revision hopefully the preinstall will fix it. Also I have the voice manual install manual both dont see how to default it can anyone help can I just default the voice mail card?
Thanks Again..
Mike

Re: SVMI-4 Wont interface in Compact DCS
#440304 09/19/11 07:55 AM
Joined: Jun 2005
Posts: 574
Member
Offline
Member
Joined: Jun 2005
Posts: 574
To default the configuration quit application and get to c:/ promt type in default and follow instructions
note no custom promts will be removed and system password wont change either

Re: SVMI-4 Wont interface in Compact DCS
#440305 09/19/11 03:14 PM
Joined: May 2001
Posts: 175
fldiver Offline OP
Member
OP Offline
Member
Joined: May 2001
Posts: 175
you da man thank you sure...trying it now....

Re: SVMI-4 Wont interface in Compact DCS
#440306 09/19/11 03:22 PM
Joined: May 2001
Posts: 175
fldiver Offline OP
Member
OP Offline
Member
Joined: May 2001
Posts: 175
it seems to be working so its confirmed you are definetely DA-MAN.....


Moderated by  Genesiscomm, nameless, pvj 

Link Copied to Clipboard
Forum Search
Most Recent 5 Post
SV9100 Blue
by conxtel - 05/26/20 03:35 PM
No UM audio
by ILE - 05/26/20 02:14 PM
KXTD816 ringing wrong extension
by ToshiGal75 - 05/25/20 06:02 PM
SV9100 with 10 digit DIDs on SIP
by conxtel - 05/22/20 08:58 PM
SV9100 CP20 Question
by erniejoey - 05/22/20 11:41 AM
Who's Online Now
36 members (justbill, Memphisribs, dans, Curlycord, dexman, Daniel, pdxjim911, Professor Shadow, hbiss, Meyery2k, Biztel Cuban Okie Tech, RATHER BE FISHING, newtecky, conxtel, tylan, CSB, ILE, Touch Tone Tommy, Bezzor, westerntelephone, KRRath, mike b, erniejoey, Talbot, gelehu, iatech3800, Rok1215, Droptop, Arthur P. Bloom, mongo5150, vicbob, Yoda, phonman123, Skunky, morephones, nortelvoip), 497 guests, and 56 robots.
Key: Admin, Global Mod, Mod
Popular Topics (Views)
Forum Statistics
Forums95
Topics93,720
Posts635,863
Members49,287
Most Online5,661
May 23rd, 2018
Today's Birthdays
kevitosc, MJK
Newest Members
Taulbs, nikauri, Darrel Mullins, fleming23, AKP
49287 Registered Users
Get Tech Support Now! Click the banner below
Get Tech Support Now!
EMP & Lightning Home Surge Protection
EMP - Click Here!
Top Posters (30 Days)
Bob-o 14
dexman 9
ILE 9
Bluewater Sailing
https://www.patreon.com/bePatron?u=5256033
EMP Shield for Commercial - Home & Vehicle
Use Coupon code SAVE - Click Here!
Servpro Ventura 24-Hour Emergency Service
Free Estimates call us now 24Hours
Contact Us | Telephone System Tech Support | Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers.
©Copyright Sundance Communications 1998-2020
Trusted Partners