web statisticsweb stats

Business Phone Systems

Previous Thread
Next Thread
Print Thread
Rate Thread
Joined: May 2006
Posts: 18
Member
Member
Offline
Joined: May 2006
Posts: 18
I am hoping someone can help point me in the right direction.

We are intending to connect our ECS v3 with a non-Iwatsu remote PBX using E&M. The intent being that local users would be able to dial extensions and connect to the remote site. All traffic would flow over a site to site VPN.

Since Iwatsu E&M is proprietary, we cannot use an Iwatsu E&M card, so we have setup a T1 & Receiver card to be used with the E&M.

The intent is that the ECS T1 card connects to a Cisco router with a T1 card in it. Then travels out of the Cisco over the VPN as IP and into another Cisco router at the remote site that is already setup with an E&M card directly to the Erikson PBX. (E&M type 2)

So Far, in theory, so good.

Unfortunately, I am not able to find any documentation on setting up the ECS T1 card for this purpose.
Any suggestions or recomendations would be greatly appreciated.

(Or PM me if you are Cisco savvy and are looking for a paid configuration challenge)

Thanks!
DP

Atcom VoIP Phones
VoIP Demo

Best VoIP Phones Canada


Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.

Joined: Aug 2006
Posts: 1,813
Likes: 15
Moderator-Iwatsu
*****
Moderator-Iwatsu
*****
Joined: Aug 2006
Posts: 1,813
Likes: 15
You could try entering the remote extension numbers in an External Networking table, and direct them to be passed out over the T1 trunk group, but this assumes you can make the Cisco equipment recognize the digits sent, then convert them into something useful for the remote switch. This is all dependent upon what kind of circuit provisioning the Cisco T1 card can provide.

Digits incoming to the ECS can be routed pretty much anywhere you want them to go, provided the Cisco can send useful info to the ECS.

It's probably way more expensive, but you may have better luck with gateways at each end.


Sometimes the thoughts in my head get so bored, they go for a stroll through my mouth. This is rarely a good thing.
Joined: May 2006
Posts: 18
Member
Member
Offline
Joined: May 2006
Posts: 18
Thank you for the reply.
Yes the Cisco T1 can be setup with any kind of provisioning needed.

Regards,
DP


Moderated by  JBean3329 

Link Copied to Clipboard
Newest Topics
Reviving an Ernest D3 payphone, Telelink, LCD
by mcgyver - 06/14/25 12:43 PM
NEC SL1100 i IP address
by teleco - 06/13/25 05:18 PM
3x8 Memory capacitor
by John807 - 06/12/25 01:14 PM
Bizarre Paging Issue
by Toner - 06/10/25 01:31 PM
Forum Statistics
Forums84
Topics94,549
Posts640,094
Members49,859
Most Online5,661
May 23rd, 2018
Newest Members
gary moore, telli, CCTechProf, Pinnacle Rich, chris c755555
49,858 Registered Users
Top Posters(30 Days)
Toner 7
hbiss 2
Who's Online Now
1 members (nortelvoip), 931 guests, and 30 robots.
Key: Admin, Global Mod, Mod
Contact Us | Sponsored by Atcom: One of the best VoIP Phone Canada Suppliers for your business telephone system!| Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers. Sundance Phone System Forums - VOIP & Cloud Phone Help
©Copyright Sundance Communications 1998 - 2025
Powered by UBB.threads™ PHP Forum Software 8.0.0