|
|
|
|
Joined: Jan 2009
Posts: 5
Member
|
|
Member
Joined: Jan 2009
Posts: 5 |
HI all
i have a PGW2200 soft switch , one Cisco GW 5400
i have created a PRI connection and i have a problem with ring back tone.
The strange is that :if i call to PRI FROM Sip , H323 , or Gsm then i can get ringback tone,..but if a call to PRI via PSTN line then i cant get ringback tone
I am looking forward for your reply
Thank you in advance
Regards
Chrisostomos
|
|
|
Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.
|
|
|
|
Joined: Jun 2007
Posts: 2,106
Member
|
|
Member
Joined: Jun 2007
Posts: 2,106 |
I think the problem may be inband versus out of band ring generation. Most VoIP protocols generate ringing at the endpoint and don't actually pass it in the audio. Beyond call set-up a PRI actually passes ringing inband like a normal telephone line. I think this might be your issue. No idea how you fix any of that or check it with your configuration.
|
|
|
|
|
Joined: Jan 2009
Posts: 5
Member
|
|
Member
Joined: Jan 2009
Posts: 5 |
Hi
First , thank you for your time
The problem is not between Voip and Pri
But between PSTN and PRI
This mean that in my GW i dont have to configure dial-peer
But only the controller , and the serial interface
Where i can find the command to change the progress indicator?
in the GW i have only this
controller E1 1/1
pri-group timeslots 1-31 service mgcp
interface Serial1/1:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn not-end-to-end 64
isdn protocol-emulate network
isdn incoming-voice modem
isdn bind-l3 backhaul SESSION-SET-PGW
isdn send-alerting
isdn sending-complete
isdn outgoing ie progress-indicator
isdn incoming alerting add-PI
no cdp enable
Thank you in advance
|
|
|
|
|
Joined: Jan 2009
Posts: 5
Member
|
|
Member
Joined: Jan 2009
Posts: 5 |
Any ideas??
Regards
Chrisostomos
Network Engineer
|
|
|
|
|
Joined: Jan 2009
Posts: 5
Member
|
|
Member
Joined: Jan 2009
Posts: 5 |
|
|
|
|
|
Joined: Feb 2005
Posts: 12,356 Likes: 4
Member
|
|
Member
Joined: Feb 2005
Posts: 12,356 Likes: 4 |
I really don't think we have anybody that can help you with this here.
-Hal
CALIFORNIA PROPOSITION 65 WARNING: Some comments made by me are known to the State of California to cause irreversible brain damage and serious mental disorders leading to confinement.
|
|
|
|
|
Joined: Jun 2007
Posts: 2,106
Member
|
|
Member
Joined: Jun 2007
Posts: 2,106 |
We posted instructions on a possible fix which is immediately dismissed. At this point it's safe to assume that the instructions are still valid and should be tested or that no one here knows what the issue is.
|
|
|
|
|
Joined: Dec 2004
Posts: 5,722
Member
|
|
Member
Joined: Dec 2004
Posts: 5,722 |
Ken
---------
|
|
|
|
|
Joined: Jan 2009
Posts: 5
Member
|
|
Member
Joined: Jan 2009
Posts: 5 |
Hi
The problem was finally in PBX configuration
|
|
|
|
Forums84
Topics94,525
Posts640,013
Members49,852
| |
Most Online5,661
May 23rd, 2018
|
|
|
|
|
|
