web statisticsweb stats

Business Phone Systems

Previous Thread
Next Thread
Print Thread
Rate Thread
#48117 04/29/06 09:55 AM
Joined: Apr 2005
Posts: 14
Member
Member
Offline
Joined: Apr 2005
Posts: 14
I have an IDS 432 that has been working fine until today.

The second cab seems to have lost the card config in sys.config.

The stations and cos are still programmed but not the card type.

I checked power before and after power supplys,
Swapped out 2nd cab acpu,
swapped out fiber jumpers between muxs,
reseated all cards,cycled power,

has anybody had this happen?

Atcom VoIP Phones
VoIP Demo

Best VoIP Phones Canada


Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.

Joined: Nov 2005
Posts: 828
Member
Member
Offline
Joined: Nov 2005
Posts: 828
Take a screen shot of both cabinets NOW. Before you do anything else. Also back up.
My guess is that you've lost communication between the cabinets - does LAN Diagnostics screen indicate that they are communicating? There's a troubleshooting section in the tech manual that goes over this issue. Good luck
Mike

Joined: Apr 2005
Posts: 14
Member
Member
Offline
Joined: Apr 2005
Posts: 14
Thanks

LAN diagnostics shows cab 1 tx at several hundred but no rx from 2

cab 2 shows all 0's and comes back with no response at the bottom.

Probably one of the muxs?

Joined: Apr 2005
Posts: 14
Member
Member
Offline
Joined: Apr 2005
Posts: 14
also I did backup everything before I started

thanks again

Joined: Nov 2005
Posts: 828
Member
Member
Offline
Joined: Nov 2005
Posts: 828
Fiber Mux is where I'd start. Re-seat again, swap fiber cable again (make certain that ends are clean). Make sure cabinet A Tx goes to Cabinet B Rx. If none work, throw hardware at it. Remember that there is a DIP switch on Fiber Mux card that designates the cabinet number. It is REALLY important that it be correctly set...
Mike

Joined: Apr 2005
Posts: 14
Member
Member
Offline
Joined: Apr 2005
Posts: 14
Swapped out fiber mux in cab 2,problem continued.

Then took original from 2,changed dip switch to cab 1 and it worked.

Problem was mux in cab 1,thanks


Moderated by  nonameyet, pvj 

Link Copied to Clipboard
Newest Topics
3515 vodavi phones.
by Gary S. - 05/01/25 12:26 PM
AT&T Coinsoft
by ChrisRR - 04/30/25 02:39 PM
Inter-tel Encore CX aka Mitel 3000 circa 2008
by Telesystems - 04/27/25 02:20 PM
Just a little of what I've been working on
by John807 - 04/25/25 11:42 AM
Forum Statistics
Forums84
Topics94,524
Posts640,007
Members49,852
Most Online5,661
May 23rd, 2018
Newest Members
DEN2MM, ferhat_efe, utec, MoverDub, Kevin usama
49,851 Registered Users
Top Posters(30 Days)
Toner 4
dexman 3
Who's Online Now
1 members (hbiss), 202 guests, and 50 robots.
Key: Admin, Global Mod, Mod
Contact Us | Sponsored by Atcom: One of the best VoIP Phone Canada Suppliers for your business telephone system!| Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers. Sundance Phone System Forums - VOIP & Cloud Phone Help
©Copyright Sundance Communications 1998 - 2025
Powered by UBB.threads™ PHP Forum Software 8.0.0