Business Phone Systems

AtcomCloud Online Store
Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 2 1 2
Joined: Nov 2008
Posts: 5
cmcbd4 Offline OP
Member
OP Offline
Member
Joined: Nov 2008
Posts: 5
Receives calls but dial pad has no tones. There are two wires with factory ends that were taped off coming out of the keypad (orange and lavender) I don't know if that has anything to do with the problem. Any input would be great.

Atcom VoIP Demo
VoIP Demo
Joined: May 2002
Posts: 17,702
Likes: 7
Member
****
Online Content
Member
****
Joined: May 2002
Posts: 17,702
Likes: 7
Anyone have a wiring diagram? Have to tried cleaning the dial contacts?


Retired phone dude
Joined: Jan 2005
Posts: 15,335
Likes: 8
Moderator-Vertical, Vodavi, 1A2, Outside Wire
*****
Offline
Moderator-Vertical, Vodavi, 1A2, Outside Wire
*****
Joined: Jan 2005
Posts: 15,335
Likes: 8
OK, here you go. This is for the -DM configuration, but since I doubt you will need A-leads, this should be all that you need:

Dial leads:

OR/BK: Network terminal C with brown switchook lead;

GN: Network terminal F with white switchook lead;

BK: Network terminal RR;

RD/GN and WH: Network terminal R with red switchook lead;

BL: Network terminal B with black handset lead;

WH/BL: Network terminal S (or any blind terminal) with green handset lead and black switchook lead;

RD: Network terminal T (or any blind terminal) with red handset lead;

Other connections:

WH lead from handset: Network terminal GN;

GN lead from switchook: Network terminal L1 with green line cord lead and black ringer lead;

YL and SL leads from switchook: Network terminal L2 with red line cord lead and red ringer lead.

SL lead from ringer coil: Network terminal K;

SL/RD lead from ringer coil: Network terminal A

***Insulate and store the following dial leads separately***

GN/WH
VI
OR


Ed Vaughn, MBSWWYPBX
Joined: Feb 2005
Posts: 12,332
Likes: 3
Member
***
Offline
Member
***
Joined: Feb 2005
Posts: 12,332
Likes: 3
Have you got the polarity correct?

-Hal


CALIFORNIA PROPOSITION 65 WARNING: Some comments made by me are known to the State of California to cause irreversible brain damage and serious mental disorders leading to confinement.
Joined: Jun 2004
Posts: 399
Member
Offline
Member
Joined: Jun 2004
Posts: 399
Sorry to confuse the issue, but I do have the BSP pages for the 2500M / 2500MM / 2500MMG and they differ from what Ed posted. I can PM or post a 6 page PDF, but basicilly I show the following for the 2500MM:

Dial leads:

OR/BK: Network terminal C with white switchook lead;

G: Network terminal F with ringer B and green line cord lead ;

BK: Network terminal RR;

RD/GN: Network terminal R with black switchook lead and handset W;

W: Network terminal GN;

BL: Network terminal B with black handset lead;

WH/BL: Network terminal S (or any blind terminal) with green handset lead and red switchook lead;

RD: Network terminal T (or any blind terminal) with red handset lead;

Other connections:


GN lead from switchook: Network terminal A with red line cord lead;

YL lead from switchook: Network terminal G with yellow line cord lead.

BR lead from switchook: Network terminal L1 with black line cord lead.

RD lead from ringer coil: Network terminal K;


***Insulate and store the following dial leads separately*** (Wires not shown on my print)

GN/WH
VI
OR

Note that the White and Blue Line cord leads were optional connections to the ringer and normally taped off.

PDF file available at:

https://www.jknichols.net/db5/00440/jknichols.net/_uimages/2500M.pdf

Joined: Jan 2005
Posts: 15,335
Likes: 8
Moderator-Vertical, Vodavi, 1A2, Outside Wire
*****
Offline
Moderator-Vertical, Vodavi, 1A2, Outside Wire
*****
Joined: Jan 2005
Posts: 15,335
Likes: 8
That is not a problem at all and you certainly are not confusing the issue. I was just recalling the -DM equivalent (non-A lead) wiring from memory. Thanks for posting the real stuff.

By the way, I suspect that the dial was replaced at some point with a speakerphone-compatible one and the spare switching leads were just insulated and stored. I'm sure that's why they didn't show up in your diagram.


Ed Vaughn, MBSWWYPBX
Joined: Jun 2004
Posts: 399
Member
Offline
Member
Joined: Jun 2004
Posts: 399
Also, the 2500MM originally had a type 35 dial that WAS polarity sensitive, but could be upgraded to a 2500MMG with a type 71 dial that did not care about polarity - can you find a code number on the dial with either 35 or 71 in it?

Correct me if I'm wrong, but I think that the Red (ring) wire should be negative 48 volt relative to ground and the Green (tip) wire should be close to Ground

Joined: Feb 2005
Posts: 12,332
Likes: 3
Member
***
Offline
Member
***
Joined: Feb 2005
Posts: 12,332
Likes: 3
That's correct but the easy way to check is to just reverse them (T&R).

-Hal


CALIFORNIA PROPOSITION 65 WARNING: Some comments made by me are known to the State of California to cause irreversible brain damage and serious mental disorders leading to confinement.
Joined: Nov 2004
Posts: 290
TDS Offline
Member
Offline
Member
Joined: Nov 2004
Posts: 290

Joined: Dec 2008
Posts: 510
Member
Offline
Member
Joined: Dec 2008
Posts: 510
Several years ago we used a "polarity guard" on a customer's 2500 set that was plugged into an extension port on a Picazo system.


Bob

With all the variables involved, I am amazed when any voice and data technology works like it is supposed to.
Page 1 of 2 1 2

Moderated by  Touch Tone Tommy 

Link Copied to Clipboard
Forum Statistics
Forums84
Topics93,686
Posts636,173
Members49,606
Most Online5,661
May 23rd, 2018
Popular Topics(Views)
Today's Birthdays
cotton, JDK, jdkinney, Matt Knight, MCap, neh-telecom
Newest Members
Uranium-235, grahamw, Motel6Guy, JustAGuy, Dialtony
49,606 Registered Users
Top Posters(30 Days)
Toner 12
Yoda 9
dexman 7
Who's Online Now
1 members (dagwoodsystems), 34 guests, and 16 robots.
Key: Admin, Global Mod, Mod
Contact Us | Sponsored by Atcom: Business Phone Systems & VoIP | Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers.
©Copyright Sundance Communications 1998-2022
Powered by UBB.threads™ PHP Forum Software 7.7.5