Business Phone Systems

Previous Thread
Next Thread
Print Thread
Rate Thread
#52883 05/18/05 01:00 PM
Joined: May 2005
Posts: 29
Member
OP Offline
Member
Joined: May 2005
Posts: 29
I need help with Caller-ID. I have a Axxess/Eclipse2 version 6.0 with 3 nodes tied together with T1 cards. All CO lines are analog loop start on LSC cards and I have DKSC-16+. Is it posible to use the LSC and/or DKSC-16+ to receive caller-id information? Or, will I need a T1/E1/PRI card?

Thanks

Atcom VoIP Demo
VoIP Demo
#52884 05/18/05 07:41 PM
Joined: Aug 2001
Posts: 774
Member
Offline
Member
Joined: Aug 2001
Posts: 774
Yes, go into Individual trunk programming, and place a check in Caller ID rather than in none. (might be a drop down menu)

------------------
Voice and Data Cabling in DFW, [email protected]
DnR Communications


Voice and Data Cabling in DFW, [email protected]
DnR Communications
#52885 05/26/05 07:24 AM
Joined: May 2005
Posts: 29
Member
OP Offline
Member
Joined: May 2005
Posts: 29
Working with the CO I found out that our CO cannot provide Caller ID over an analog line. According to the manual I can use the T1/PRI (P/N 550.2740) with the PRI PAL (P/N 827.8877). In My Axxess/Eclipse version 6.0, I have the Advanced CO activated in the Premium Feature. Other than working with our CO, is there anything else I will need to purchase to get the Caller ID working.

Thanks

#52886 05/26/05 08:52 AM
Joined: May 2003
Posts: 2,267
Member
Offline
Member
Joined: May 2003
Posts: 2,267
I find it hard to believe that the telco there cannot provide CID on your copper lines. That would mean that they also cannot send it to local houses? Something sounds funny.

------------------
Avaya Telephone Repair
Intertel Telephone Repair

[This message has been edited by paul144 (edited May 26, 2005).]

#52887 05/26/05 06:39 PM
Joined: Aug 2001
Posts: 774
Member
Offline
Member
Joined: Aug 2001
Posts: 774
Quote
<font face="Verdana, Arial" size="2">Originally posted by Al_CaPhone:
Working with the CO I found out that our CO cannot provide Caller ID over an analog line. According to the manual I can use the T1/PRI (P/N 550.2740) with the PRI PAL (P/N 827.8877). In My Axxess/Eclipse version 6.0, I have the Advanced CO activated in the Premium Feature. Other than working with our CO, is there anything else I will need to purchase to get the Caller ID working.

Thanks
</font>

Sounds very funny. But test it. Call from your office to a nearby company using the same Telco Provider, and see if they recieve call id. Now if with a very small mom and pop CLEC then they may not be able to provide caller ID, and you may find it hard to locate another customer of theres nearby.

------------------
Voice and Data Cabling in DFW, [email protected]
DnR Communications


Voice and Data Cabling in DFW, [email protected]
DnR Communications

Moderated by  Stix1 

Link Copied to Clipboard
Forum Statistics
Forums84
Topics93,883
Posts637,024
Members49,675
Most Online5,661
May 23rd, 2018
Popular Topics(Views)
Today's Birthdays
Adam Randall, Felton 1967, FeltonD, paezacero, Spencer
Newest Members
tech3500, APInc, m1cashman, jonnycom, XJR9000
49,674 Registered Users
Top Posters(30 Days)
Toner 11
jsaad 8
teleco 6
dexman 5
Shahza 4
Who's Online Now
0 members (), 73 guests, and 19 robots.
Key: Admin, Global Mod, Mod
Contact Us | Sponsored by Atcom: Business Phone Systems | Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers.
©Copyright Sundance Communications 1998-2023
Powered by UBB.threads™ PHP Forum Software 7.7.5