|
|
Joined: Jun 2005
Posts: 25
Member
|
|
Member
Joined: Jun 2005
Posts: 25 |
Hello All - Replaced a DK40I after Sandy swept thru. After using 91-9 to initialize, ports 000 thru 003 were dead. Before
91-9 those ports worked. Any clue?
Thanks in advance
|
|
|
Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.
|
|
|
|
Joined: Mar 2001
Posts: 3,869
Member
|
|
Member
Joined: Mar 2001
Posts: 3,869 |
I would look at the amphenol to see that it is seated properly and then run the programming again, extremely rare to see a tosh do a dump like that, usually a mechanical problem more than the tosh itself.
You can run the software check program and see if that shows anything.
THE Bracha, old blond specialist in Rube Goldberg solutions.
|
|
|
|
|
Joined: Apr 2004
Posts: 4,991
Member
|
|
Member
Joined: Apr 2004
Posts: 4,991 |
Was that Amphenol connector in water [salt water]?
|
|
|
|
|
Joined: Mar 2001
Posts: 3,869
Member
|
|
Member
Joined: Mar 2001
Posts: 3,869 |
Come to think of it and I apologize for not thinking of it before, were the jacks wet? Did you bench test this? Maybe the previous ksu is good and the wiring is bad at the jacks, of course if the DK40 was under salt water with power on then well no it is beyond hope.
THE Bracha, old blond specialist in Rube Goldberg solutions.
|
|
|
|
|
Joined: Jun 2005
Posts: 25
Member
|
|
Member
Joined: Jun 2005
Posts: 25 |
Replaced both amphenols at the DK. One to main, one to expansion.What has me is AFTER I swapped out system, went to working port 000, initialized 91-9, then ports 000-003 went dead...
|
|
|
|
|
Joined: Apr 2004
Posts: 4,991
Member
|
|
Member
Joined: Apr 2004
Posts: 4,991 |
What parts of this systems parts were wet,system,mdf ,cables and jacks
Punch down a jack on 000 right at the mdf and plug in a phone
|
|
|
|
|
Joined: Jun 2005
Posts: 25
Member
|
|
Member
Joined: Jun 2005
Posts: 25 |
Had all x-conn off all ports. Puched test jack on 000 thru 003, nothing. I do hear tones when i depress buttons on those ports, so i am getting juice. Also reset the power on the breakers next to power supply.Again those ports worked BEFORE 91-9 was done. Strange
|
|
|
|
|
Joined: Jan 2006
Posts: 2,266 Likes: 1
Member
|
|
Member
Joined: Jan 2006
Posts: 2,266 Likes: 1 |
Make sure your amp cable is connected good, I have had the same problem and the amp cable had a screw that needed to be backed out on the top to get the cable to connect good.
|
|
|
|
|
Joined: Jun 2003
Posts: 3,273 Likes: 1
Moderator-Toshiba
|
|
Moderator-Toshiba
Joined: Jun 2003
Posts: 3,273 Likes: 1 |
Remove the power from the DK and strap the battery to the off position for about a minute and then put it back and power it on.
|
|
|
|
|
Joined: Mar 2001
Posts: 3,869
Member
|
|
Member
Joined: Mar 2001
Posts: 3,869 |
What was actually underwater that you know of?
Did you test the old ksu back at your place or are you sure it was just destroyed?
As Steve says, the physical connection of the amp not fitting in tight is one I've had before and did you run program 00, the software check?
Could also be a bad cable, I always have a 25 pair RJ11 breakout block in the car from Graybar, a lifesaver for testing at the ksu.
THE Bracha, old blond specialist in Rube Goldberg solutions.
|
|
|
|
Forums84
Topics94,515
Posts639,967
Members49,848
| |
Most Online5,661
May 23rd, 2018
|
|
|
0 members (),
288
guests, and
33
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
|
