|
Joined: Feb 2013
Posts: 122
Member
|
Member
Joined: Feb 2013
Posts: 122 |
Dear All ,
i have a strange when the user dial 9 and pickup the PRI trunk then dial the number the digital phone take 10 seconds before ring back tone recieve :)with analogue phone the call disconnect because this delay
how i can reduce this delay ?
Thanks
NEC Business Partner Certified on SV8100,SV8500,SL1000
|
|
|
Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.
|
|
|
Joined: Apr 2007
Posts: 1,439
Member
|
Member
Joined: Apr 2007
Posts: 1,439 |
are you using LCR programming or direct access?
In CM200 what is 9 set to?
D
|
|
|
|
Joined: Feb 2013
Posts: 122
Member
|
Member
Joined: Feb 2013
Posts: 122 |
NEC Business Partner Certified on SV8100,SV8500,SL1000
|
|
|
|
Joined: Feb 2013
Posts: 122
Member
|
Member
Joined: Feb 2013
Posts: 122 |
Also there is no command like CM200
please advise
NEC Business Partner Certified on SV8100,SV8500,SL1000
|
|
|
|
Joined: Jul 2001
Posts: 1,985
Moderator-Mitel, NEC, Vodavi
|
Moderator-Mitel, NEC, Vodavi
Joined: Jul 2001
Posts: 1,985 |
Yes, there is a cm200, your issue is likely in cm85x, if you are using LCR. If you don't understand that verbiage, time to call a tech. I charge a fees for in-depth assistance such as this.
|
|
|
|
Joined: Dec 2008
Posts: 189
Member
|
Member
Joined: Dec 2008
Posts: 189 |
The command is actually 20x.
|
|
|
|
Joined: Apr 2007
Posts: 1,439
Member
|
Member
Joined: Apr 2007
Posts: 1,439 |
1. Take note of, or set the sense wheel on the 24PRTA/B/C card e.g. 06 2. CM 050>06>12Set the Sense wheel of the 24PRT card (06) to a type 12for ISDN PRI. 3. CM 0608>0>06Set the DCH channel (0~7) to the sense wheel of the 24PRT card (06). 4. CM 0701>0600~0623>D200~D223To the sense wheel of the 24PRT card (06), assign to each channel (00~23) a trunk (D200~D223). All channels should be assigned. 5. CM 3000>200~222>20 Place each Voice trunk (200~222) assigned in step 4, to a trunk route (20). CM 3000>223>21 Place the D channel trunk (223) assigned in step 4 to its own trunk route (21). NOTE:this must be the 24 th channel of the span. 6. CM 3002>200-222>18Assign each Voice trunk (200~222) to ISDN in-dial (18) in Day Mode. 7. CM 3003>200-222>18 Assign each Voice trunk (200~222) to ISDN in-dial (18) in Night Mode. 8. CM 3040>200-222>18Assign each Voice trunk (200~222) to ISDN in-dial (18) in Mode A. 9. CM 3041>200-222>18Assign each Voice trunk (200~222) to ISDN in-dial (18) in Mode B. 10. CM 3007>200-222>000-022To each Voice trunk (200~222) set a Circuit Identification Code (CIC, 000~022). NOTE:No CIC should be assigned to the D channel trunk (223). 11. CM 3500>20>00 Set the voice trunk route (20) type to CO (00). 12. CM 3504>20>2 Set the voice trunk route (20) to Answer signal arrives (2). 13. CM 3509>20>08Set the voice trunk route (20) to ISDN incoming signaling (08). 14. CM 3516>20>0 Set the voice trunk route (20) to Sending of Hook Flash disabled (0). 15. CM 3518>20>0 Set the voice trunk route (20) to allow DID/DNIS digit conversion with CM 76 (0). 16. CM 3528>20>0Set the voice trunk route (20) to disallow Trunk Queuing. 17. CM 3590>20>3Set the voice trunk route (20) to ISDN PRI. CM 3590>21>3Set the D channel trunk route (21) to ISDN PRI. NOTE:This is the onlyCM 35 bit set for the D channel trunk route (21). 18. CM 3593>20>00 Assign the Voice trunk route (20) to the ISDN DCH channel set in Step 2. 19. CM A900>0>223 Assign the DCH channel (0) to the DCH trunk (223). NOTE:this must be the 24 th channel of the span. 20. CM 410>50>05 Set the timing start for ISDN calls to 5seconds. CM 410>57>05 Set the timing start for ISDN tandem calls to 5 seconds. 21. CM 482>04>0 Enable 2 nd dial tone sending on ISDN trunks. 22. CM AA00>06>0 Set the sense wheel of the 24PRT card (06) to AT&T Specifications (0). 23. CM AA06>06>20/21/28To the 24PRT sense wheel (06) assign an ISDN protocol. 20= AT&T, 21= Northern,28= NI2. 24. CM AA14>06>0/1 For the sense wheel of the 24PRT (06) card assign the type of ISDN card being utilized. 0= 24PRT, 1= SC01.
|
|
|
Forums84
Topics94,512
Posts639,933
Members49,844
|
Most Online5,661 May 23rd, 2018
|
|
1 members (muddybl),
228
guests, and
37
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|