Business Phone Systems

Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 2 1 2
#567329 02/28/14 05:12 PM
Joined: Feb 2006
Posts: 148
Member
OP Offline
Member
Joined: Feb 2006
Posts: 148
hello trying to forward analog ext 2102 to external cell phone anyone know how to do this when I go off hook from ext 2102 and dial * get a fast busy thought it was off hook *4 9 plus the cell number any insight would be much appreciated thanks


Danny
Atcom VoIP Demo
VoIP Demo
Joined: Jan 2005
Posts: 15,346
Likes: 10
Moderator-Vertical, Vodavi, 1A2, Outside Wire
*****
Online Content
Moderator-Vertical, Vodavi, 1A2, Outside Wire
*****
Joined: Jan 2005
Posts: 15,346
Likes: 10
Don't you have to push the feature button first?


Ed Vaughn, MBSWWYPBX
Joined: Feb 2005
Posts: 1,610
Member
Offline
Member
Joined: Feb 2005
Posts: 1,610
-you need 4.1 software
-you need to build a route and dest code (forward to dest code then cell#)
-you need to do Flash/Link then * as if pressing Feature

Link/Flash + * + DestCode + Cell#

See if that helps



=---()))))))))---=
www.curlycord.com
[Linked Image from telcopc.ca]
Toronto, Canada




Joined: Dec 2003
Posts: 2,086
Moderator-Nortel
Offline
Moderator-Nortel
Joined: Dec 2003
Posts: 2,086
Hook *4 is forwarding your phone - not what you want to do.
You really are trying to Transfer your call to cell phone.

Hook *70 9 Cell#

BUT - you also can't have line pool access code. (dial 9)
You have to use routing. (dial 9)
Analog needs 2 IC's and (I can't remember for sure)maybe allow redirect.


If CON is the opposite of PRO
Then what is the opposite of Progress?
NTlayoff #567344 02/28/14 07:13 PM
Joined: Dec 2003
Posts: 2,086
Moderator-Nortel
Offline
Moderator-Nortel
Joined: Dec 2003
Posts: 2,086
Maine Phone Man

I just re-read your post.
Are you trying to put a Permanent forward on your analog phone?

If yes, then it would be *4 not *70 but then the rest of the reply is good.


If CON is the opposite of PRO
Then what is the opposite of Progress?
Joined: Feb 2006
Posts: 148
Member
OP Offline
Member
Joined: Feb 2006
Posts: 148
Yes want to forward all calls to internal single line ext 2102 to cell phone,,, phone is a single line set no feature key when you dial * you get a fast busy


Danny
Joined: Oct 2012
Posts: 249
Member
Offline
Member
Joined: Oct 2012
Posts: 249
As Curly stated, in order to setup call forwarding on a single line set, you have to Flash/Link then press the * key before entering the feature code - if you are simply picking up the handset and dialing *, then you will get a busy signal as you are supposed to. If you Flash/Link * 4 and dial 9 plus the phone number with the assumptions that you have 4.1 or above and have programmed a route with "9" for line pool access then all should work fine.


www.highspeedtele.com
Dallas & Fort Worth, TX
Joined: Feb 2006
Posts: 148
Member
OP Offline
Member
Joined: Feb 2006
Posts: 148
pool is 9 dest code is 9 when you flash line dial tone is gone dial a * 4 dial is present 9 plus cell


Danny
Joined: Feb 2005
Posts: 1,610
Member
Offline
Member
Joined: Feb 2005
Posts: 1,610
Yes I forgot the 4 but seems he meant what I knew lol
Link/Flash + * + 4 + DestCode + Cell#

As mentioned 3 times you need to use a Route, not Pool.

Recap with all of above mentioned:

-You need 4.1 software or above (you still have not confirmed what software you have)
-Build route 010 and tell it to use your existing pool
-create dest code of 7 and tell it to use route 010
-Assign 2 Intercom paths to the DN of ATA
-set Allow Redirect to Yes

Try that and see if still an issue.








=---()))))))))---=
www.curlycord.com
[Linked Image from telcopc.ca]
Toronto, Canada




Joined: Oct 2012
Posts: 249
Member
Offline
Member
Joined: Oct 2012
Posts: 249
One last thing - you mentioned Pool is 9 - Pool is most likely A, but if you mean you set up an Access Code of 9, you need to remove it - it will conflict with the destination code of 9.


www.highspeedtele.com
Dallas & Fort Worth, TX
Page 1 of 2 1 2

Moderated by  MooreTel, NTlayoff 

Link Copied to Clipboard
Forum Statistics
Forums84
Topics93,739
Posts636,410
Members49,616
Most Online5,661
May 23rd, 2018
Popular Topics(Views)
Today's Birthdays
David Gillish, jkdawsey, kitjr123, MP Telecom, stephen1905
Newest Members
Lane, AMS Technology C, Chrontel, RonZ1971, Michael1948
49,616 Registered Users
Top Posters(30 Days)
Toner 9
jsaad 7
Who's Online Now
0 members (), 64 guests, and 15 robots.
Key: Admin, Global Mod, Mod
Contact Us | Sponsored by Atcom: Business Phone Systems | Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers.
©Copyright Sundance Communications 1998-2022
Powered by UBB.threads™ PHP Forum Software 7.7.5