|
|
Joined: Feb 2005
Posts: 12,344 Likes: 3
Member
|
Member
Joined: Feb 2005
Posts: 12,344 Likes: 3 |
Use program fields 700-702 to enable the doorphone. Did you actually check this or do you want to just keep asking questions? -Hal
CALIFORNIA PROPOSITION 65 WARNING: Some comments made by me are known to the State of California to cause irreversible brain damage and serious mental disorders leading to confinement.
|
|
|
Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.
|
|
|
|
Joined: Feb 2017
Posts: 9
Member
|
|
OP
Member
Joined: Feb 2017
Posts: 9 |
i will do that . i have to figure that out. Just asking as many questions as i can before diving back in . I am an IT/Network guy. I am working my way through the manual. Thanks I will check before reposting.
|
|
|
|
|
Joined: Feb 2017
Posts: 9
Member
|
|
OP
Member
Joined: Feb 2017
Posts: 9 |
Well i cant get into programming mode.I have the software, i connected tried the defualt password. doesnt work.
I tried resetting to default. I put the unit in clear mode turned it on , and waited till i had a steady flash then held the reset button for 3 seconds. still says wrong password. i also tried first putting it back to normal mode (found this online ) and then holding the reset button. Any ideas how to reset?
Last edited by skip555; 02/10/17 08:56 PM. Reason: remove password
|
|
|
|
|
Joined: Jun 2006
Posts: 211
Member
|
|
Member
Joined: Jun 2006
Posts: 211 |
Check page 84 of the installation manual for the correct reset procedure.
It would also be a good idea to back up the configuration before you default the system, in case you have trouble duplicating the old settings. Instructions to do so can be found in section 5.7 of the programming manual. This assumes you are able to recover the password - the original documentation/dealer who installed the system would be a good place to start.
|
|
|
|
|
Joined: Feb 2017
Posts: 9
Member
|
|
OP
Member
Joined: Feb 2017
Posts: 9 |
I cant find a way to back up the system without the password to get into it.
Dealer who installed also installed an alarm and cameras and seriously defrauded me. So that isn't an option.
On page 84 it says to press reset before it stops flashing. Is that the fast flash or the slow flash that happens after a few seconds
Last edited by bennuss; 02/10/17 05:58 PM.
|
|
|
|
|
Joined: Jan 2004
Posts: 6,648
RIP Moderator-Nisuko-Tie, General
|
|
RIP Moderator-Nisuko-Tie, General
Joined: Jan 2004
Posts: 6,648 |
a Panasonic Dealer can reset the password for you and help you out with the Doorbox issues if your not happy with the installing dealer , look for another Password resets and system resets aren't allowed in the open forums here Please do not post passwords or any other privileged information in the public forums. As a rule of thumb, if the information is not in the users or administrators guide, do not post it in the forum. If you wish to relate such information in regard to a post, you should do this by sending a private message or an email to the poster.
Skip
------------------------------------
Serving SW and West central Fl since 1984
|
|
|
|
Forums84
Topics94,291
Posts638,805
Members49,767
| |
Most Online5,661
May 23rd, 2018
|
|
|
2 members (Toner, justbill),
168
guests, and
396
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
|
