sundance-communications.com/forum Forums TDM Business Telephone Systems Avaya - Lucent Telephones & Systems First PRI !!!

This will be my first PRI and I have two weeks to program before the cut. I have done three basic magix but lots of Partners.

In any case I have the quick ref book, the Feature Ref book but no step by step programming manual. ANY help would be greatly appreciated. any manual...

Thanks

Rich

email me your fax number and i can send you a quick reference sheet i was given.

You have mail

Can you fax me that quick reference sheet too,, my fax is 850 983-9875

Could I have a copy also please ? Fax # is 510-534-5253 thank you.

Thanks to Gkar, G Flash and Rick Geloff, great help and i got the PRI up! now to get the DID's set up. lol

rs

Could I also get a copy of the PRI sheet.
Thanks

I would also really appreciate a copy of this. Thanks in advance

Hereis what I use, now no one will be bothered to have it faxed.

Switch must be on Hybrid Mode

1. Set Frame Format to Extended Super Frame
Lines Trunks=>LS/GS/DS1=>enter slot + Enter =>Frame Format=>Extended Super Frame=>Enter.

2. Set Suppression
Lines Trunks=>LS/GS/DS1=>enter slot + Enter =>Suppression=>B8ZS=>Enter.

3. Change Type to PRI.
Lines Trunks=>LS/GS/DS1=>enter slot + Enter =>Type=>PRI=>Enter.

PRI MENU

4. Set Switch Type.
Lines Trunks=>PRI=>Switch Type=>make choice+Enter.

5. Program B-Channel Group.
B-Channel Group=>B-Channel=>When prompted for b-channel group, type 1+ Enter.
When prompted for B-Channels, enter in the form: slot/B-Channel(sspp)
starting with B-Channel 23 and working down to B-Channel 1. Example: if slot is 4,
type 0423, enter, 0422, enter, 0421, enter, ect……….0401.
Return to B-Channel Group menu.

6. Program Lines.
Lines=> when prompted for b-channel group, type 1 + Enter=>enter line trunks (1st 23 only).
Return to B-Channel Group menu.

7. Set Network Service.
Ntwk Svc=>Misc=>CallByCall=>Enter.
Return to B-Channel Group menu.

8. Set Incoming Routing.
Incoming Rtg=>Dial Plan=>Enter.
Return to B-Channel Group menu.

Back

9. Program Dial Plan Routing.
Dial PlanRouting=>Service=>0=>Misc=>Any=>Enter.
Exit back through Dial Plan Rtg menu to PRI menu.

Back

10. Program Outgoing Table.
Outgoing Table=>CBC Svc=>Pattern=>when prompted for list and entry numbers, enter 00=>Enter.
When prompted for pattern number, enter: 0=>Next(F9)=>1=>Next=>2=>Next……..8=>Next=>9=>Enter.

Back

11. Set Network Service.
Ntwk Svc=>Misc=>No=>Enter.

If this is a general use PRI, you must change the Special Service Table as follows:
PRI=>Outgoing Table=>Special Svc=>Del Digit=>When prompted for entry number, enter 0 + Enter.
Change entry to 0=>Next=>change entry to 0=>Next, ect until all entrys, 0-7 are 0.

If this is a strictly long-distance PRI, leave the Del Digit values at default.

INFO for PRI Provider

- PRI ESF B8ZS
- The Terminal Equipment Identifier (TEI) = 0
- Switch Type: 5ESS
- Optioned for "Custom"

If switch type is DMS-100, The protocol MUST be set for “NTNAPRI”. Additionally, if the switch type is DMS-100, the field “L1 flags” in the “Trunk Sub Group” table should be set to yes. This is more critical when using DS1
cards with an Apparatus code beginning with “517M”. These particular DS1 boards WILL NOT work properly without this parameter set.