web statisticsweb stats Business Phone Systems Tech Talk Forum - VOIP & Cloud Phone Help

Business Phone Systems

Previous Thread
Next Thread
Print Thread
Rate Thread
#73351 02/04/05 11:22 AM
Joined: Jun 2004
Posts: 65
kingtel Offline OP
Member
OP Offline
Member
Joined: Jun 2004
Posts: 65
It's been a long time since I have touched one these systems and need some help with identifying this legend or Merlin 2. I need to program some new lines onto a few sets.
I took a MLX-20 out to the job site to program the new lines, but system did not have a MLX card installed.
My oldest AT&T Merlin Legend system program manual says use a MLX 20 or SPM software which I'm now looking for.
My first ? - Is it possible this is a Merlin 2 and can be programmed with a hybrid set on sta 10. The processor is labled "Large System equiped with FM2". Has a SMDR and Admin port. If it is a Merlin 2, what are program codes or a source I can codes & proceures from to add lines.
If it's a Legend 2.0 where can I get SPM software.
Need advice and help with setup and programming.
Sorry this got long.
Thanks a ton for any advice and procedure tips.

Rich

Avaya IP Office Help & Support Website
IP Office Help

Avaya IP Office Help & Support Website


FAQs, documentation, videos, updates, and support for the Avaya IP Office business phone system!
Everything you need to know about installing, upgrading, and troubleshooting IP 500v2 and IPO Server Edition systems.

#73352 02/04/05 12:56 PM
Joined: Aug 2003
Posts: 226
JBW Offline
Member
Offline
Member
Joined: Aug 2003
Posts: 226
https://support.avaya.com/japple/cs...ct=143445&temp.selectedBucket=108025
The avaya support site has the spm on it for free. I think you may have the legend processor. Do you have a single line card in the system.
JBW

#73353 02/04/05 01:53 PM
Joined: Mar 2004
Posts: 253
Member
Offline
Member
Joined: Mar 2004
Posts: 253
i think its a merlin two if it said fm2 on the processor. what voicemail do they have? that would tell the story..

[This message has been edited by locg (edited February 04, 2005).]

#73354 02/04/05 04:19 PM
Joined: Jun 2004
Posts: 65
kingtel Offline OP
Member
OP Offline
Member
Joined: Jun 2004
Posts: 65
Reply to JBW & locg : Yes it does have a 012 analog sta card in the last occupied slot, with 3 ports patched to a Compaq Deskpro 575 PC. From what I could see, it did not look like any AT&T VM.
Main screen had GVM Systems in upper left corner. Prior to the 012 card is two 408 cards. ( not 408 GS/LS cards )
The processor does not have a PCMIA slot, or fault indicator above it. Just SMDR & Admin ports.
I'm leaning towards a Merlin 2 vs Ledgend.
If it is a M2, can it be programmed with a BIS 22 set.
I'm searching for a downloadable Merlin 2 FP2 program manual in hope it can anwser some of my questions.
Anymore feedback or opinions would be greatly appreciated.

Thanks

#73355 02/04/05 05:05 PM
Joined: Aug 2003
Posts: 226
JBW Offline
Member
Offline
Member
Joined: Aug 2003
Posts: 226
I seem to remember a legend r2 and I don't recollect that it had the pcm slots but it did have a mlx card in the 1st slot. Any way you can program some features by sliding the switch on the phone to the p position, pressing a button, and entering a feature code. I have a legend r2 manual and the r2 analog multiline telephones users guide if you need any specific codes from the manuals I have. If you have a merlin II my manual shows that you can program it with a BIS34D by
place prgrm overlay on ext 10
enter programming
1 - touch admin tel
2 - touch the auto intercom button for the voice terminal you're programming
3 - touch and lite the appropriate line buttons to be added to this voice terminal
exit programming
This applies to a system in the square mode.
If anyone can explain this better feel free to hop in.
JBW


[This message has been edited by JBW (edited February 04, 2005).]

#73356 02/05/05 09:48 AM
Joined: Mar 2004
Posts: 253
Member
Offline
Member
Joined: Mar 2004
Posts: 253
i think you slide the switch down on the left of ext 10 that programming mode. you need a manual its pretty easy to program.

#73357 02/05/05 10:29 AM
Joined: Nov 2001
Posts: 1,640
Moderator-NEC
*****
Offline
Moderator-NEC
*****
Joined: Nov 2001
Posts: 1,640
Does the processor have the big 96pin diagnostic header on the processor, If it does it's a Merlin II

The fact that it has a port labeled ADMIN leads me to believe it is a legend. Go to a phone and dial *10 - do you hear a modem tone. Also remember the OLD legends only connect a t 1200 baud using SPM or WinSPM. (yes you can use Winspm but you won't get quick access and you basically bet Standard SPM emulation)

~Don~

#73358 02/08/05 10:34 AM
Joined: Jun 2004
Posts: 65
kingtel Offline OP
Member
OP Offline
Member
Joined: Jun 2004
Posts: 65
Thanks guys,

You comments and anwsers stirred up some stagnet grey matter.
I was able able to access the system with WIN SPM and and take care of the line adds and changes without a hitch. Turns out the system is Legend rel 2.1 v4.0

Rich


Link Copied to Clipboard
Forum Statistics
Forums84
Topics94,262
Posts638,697
Members49,757
Most Online5,661
May 23rd, 2018
Popular Topics(Views)
211,100 Shoretel
187,712 CTX100 install
186,800 1a2 system
Newest Members
BPopilek, Rich F, LewisR, TDKs79, Buttinset
49,757 Registered Users
Top Posters(30 Days)
dexman 18
Toner 11
TDKs79 8
teleco 4
Who's Online Now
0 members (), 140 guests, and 24 robots.
Key: Admin, Global Mod, Mod
Contact Us | Sponsored by Atcom: One of the best VoIP Phone Canada Suppliers for your business telephone system!| Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers. Sundance Phone System Forums - VOIP & Cloud Phone Help
©Copyright Sundance Communications 1998-2024
Powered by UBB.threads™ PHP Forum Software 7.7.5