OK here you go this will remove the # from the dialing: You access the Maintenance menu
Then go to Diagnostics menu Clt-C then N for Software Diagnostics menu:
You will then go to Tie Groups 1 section : Since the Tie Group you are using you will have to Tap over to the 9th group
Right now it reads 00 (TIE GROUPS 1 00 00 00 00 00 00 00 00 00 00) )
(To get there use the Enter key and once on Release Tie Y Hit the Tap Key) (Then Tap over to the 9th 00 Entry)
Then enter 01 to remove the # from the Transfer sequence,
(Yes it use to be a Debug) I do believe this will resolve the issue.


S/W DIAGNOSTICS MENU [C]AB 01
––––––––––––––––––––––––––––––––
SOFT RESET: 103019 102095 STK FRM:0C01 0000 00000000 005A 0000 00000000
[W]ATCH DOG: 18 18 01 00000000 00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000 00000000
MAINT ON : Y [M]AINT DATA: 0000 00 00 00 00 00 00 00 00 00 00 00
01 0000 00 00 00 00 00 00 00 00 00 00 00
RELEASE TIE: Y TIE GROUPS 1 00 00 00 00 00 00 00 00 00 00
RST DISABLE: N GROUND TRUNK: N
AGNT RFRESH: 005 ALRM CLK OFF: N
TEST MODE : N SLI HOOK DEB: N
PICK ENABLE: N SLI PBX CONF: N
RCVR VOL : 13 NO_BUSY_TONE: N
T1RCVR VOL : 10 VMS 140 CODE: 4
DTMF VOL : 08 SLI RCV TIME: 60
RCRD VOL : 13 TOLL TIMEOUT: 03
PILOT ICM : N PRIME RING : 06
VMS DISCONN: N SECOND RING : 09
DIVERT VOL : 00 RELAY EXT : 0000
PRTN TIMER : 120 RELAY RATE : 000
ALARM VOL : 06 ACD TSF TIME: 019
WRAP UP OPT: N DIAL 10 : N
REL KEY DEB: N SMDI_DIAL :080

I drink Bush (Cheap) Beer Let us know if it resolves the issue.
I wouldn't change anything on the Executone trunk group you are using as it is working
IF it's NOT broke don't fix it as they say.

4.11.7 Tie Group 1 & 2
Use Tie Group 1 for Trunk Groups 1 to 10. Use Tie Group 2 for Trunk Groups 11 to 20. Use
the I and D keys to change between Tie Group 1 and Tie Group 2. Program each of the trunk
groups to be used as Release Link Tie Lines as follows:
• 01 – to remove the DTMF # on CO transfers across tie lines.
• 02 – to provide a flash on the tie line group for the programmed Flash Timer.
• 03 – to both remove the DTMF # on CO transfers across tie lines and to provide a
flash on the tie line group for the programmed Flash Timer.
• 04 – This allows the system to serve as a tandem switching system. Programming a
group for 04 allows incoming tie line calls to reference the translation tables (DID
Programming and Transparent Intercom Dialing screens) and be routed back out of the
system on another tie line group. Programming a group for 04 allows a call that was
routed of the system to be transferred back to an extension in the system. Without the
04, if a call is transferred back to the system the flash and digits would be sent to the
carrier instead of being detected as a transfer.

And YES the OLD (Retired Executone System Will DO More that other's think. What a shame it was put off to the side) Just my feelings
they had such potential and GREED knocked it out but many other future systems were developed off it's features and what it could do.

Sorry it took so long to respond but new work takes priority right now..


Last edited by mc601; 12/01/17 09:39 PM. Reason: improvement
mjc