Business Phone Systems

Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 3 1 2 3
#133937 06/07/07 08:28 PM
Joined: Nov 2003
Posts: 1,313
Member
OP Offline
Member
Joined: Nov 2003
Posts: 1,313
i have a customer with a mics. that have maxed the basic cabinet out & require more stations. having confirmed with my supplier what i needed i got it. i got a 0X16 fiber station module, 1 fiber nam, and a 6 port fiber expansion card.

i turned off the system. plugged in the 6 port expansion into slot #1 & booted system up. display on 221 showed configuration error. so for fun i put it into slot 2 & same error. so i tried defaulting the system & then installing the 6 port. the system booted up but wouldn't let me into programming. kept saying: in use mega-sr.

i waited for 20 minutes. still same error. finally had to take it out & re-program whole system back the way it was.

why is this happening? i know i can have 2-6 port expansion cards in the system (per the manual).

my software version is: sp 30meF02 NAT

the software cartridge info:
nntm040c08cc
rel 01b
1998/08/26
na-mics 3.0
v5.02

Atcom VoIP Demo
VoIP Demo
#133938 06/07/07 08:37 PM
Joined: Aug 2004
Posts: 9,108
Likes: 10
Admin
*****
Offline
Admin
*****
Joined: Aug 2004
Posts: 9,108
Likes: 10
You can only have the 2nd 6 port expansion if you have the mega software.


[Linked Image]
#133939 06/07/07 08:43 PM
Joined: Nov 2003
Posts: 1,313
Member
OP Offline
Member
Joined: Nov 2003
Posts: 1,313
currently there are no 6 port expansion cards in the system. i was adding the 1st. so would that mean that i would still need the mega software in order to use the 1st one?

#133940 06/07/07 09:10 PM
Joined: Aug 2004
Posts: 9,108
Likes: 10
Admin
*****
Offline
Admin
*****
Joined: Aug 2004
Posts: 9,108
Likes: 10
No. Put the first 6 port in the correct slot and do the initial refresh to get it out of box condition.


[Linked Image]
#133941 06/08/07 06:07 AM
Joined: Nov 2003
Posts: 1,313
Member
OP Offline
Member
Joined: Nov 2003
Posts: 1,313
i did the **startup to default it. turned the system off. then i put it in slot #1. booted it up. from there it just sat there at the date/time & wouldn't let me get into programming. always said in use mega-sr when i tried. wouldn't even let me change the time. ended up having to just take it out (lunch was over & they needed their phones back).

#133942 06/08/07 06:15 AM
Joined: Feb 2007
Posts: 2,473
Member
Offline
Member
Joined: Feb 2007
Posts: 2,473
Depends what you concidering slot #1. It has to be second slot from the left for first 6 port expension.

#133943 06/08/07 06:24 AM
Joined: Nov 2003
Posts: 1,313
Member
OP Offline
Member
Joined: Nov 2003
Posts: 1,313
i'm talking about the 2 little skinny slots to the left of the 2 trunk cards and to the right of the power supply. they are labled #1 & #2 (with 2 being closest to the trunk cards).

i've done it before (without defaulting the system) with a 6 port copper expansion. the only thing that happened was that it forced them to go from a 2 digit number scheme to a 3 digit & i had to default the startalk because it was set for 2 digits.

#133944 06/08/07 06:35 AM
Joined: Feb 2007
Posts: 2,473
Member
Offline
Member
Joined: Feb 2007
Posts: 2,473
First 6 port expension has to be in the closest to the trunk cards slot.

#133945 06/08/07 06:50 AM
Joined: Aug 2004
Posts: 9,108
Likes: 10
Admin
*****
Offline
Admin
*****
Joined: Aug 2004
Posts: 9,108
Likes: 10
Vad is right..the fiber card has to be in the slot closest to the trunk card slots.


[Linked Image]
#133946 06/08/07 06:50 AM
Joined: Mar 2007
Posts: 85
Member
Offline
Member
Joined: Mar 2007
Posts: 85
Yep--expansion card goes into slot #2, then fiber goes into bottom connector to keep port numbering correct. Reboot the system without the expansion--then power down, install the card in slot 2--then power up again. The system should recognize the card then.

Page 1 of 3 1 2 3

Moderated by  MooreTel, NTlayoff 

Link Copied to Clipboard
Forum Statistics
Forums84
Topics93,737
Posts636,402
Members49,615
Most Online5,661
May 23rd, 2018
Popular Topics(Views)
Today's Birthdays
effedisk, hellbender, Pat Amaral, Zip
Newest Members
AMS Technology C, Chrontel, RonZ1971, Michael1948, lllDez
49,615 Registered Users
Top Posters(30 Days)
jsaad 7
Toner 6
Who's Online Now
1 members (Michael1948), 29 guests, and 23 robots.
Key: Admin, Global Mod, Mod
Contact Us | Sponsored by Atcom: Business Phone Systems | Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers.
©Copyright Sundance Communications 1998-2022
Powered by UBB.threads™ PHP Forum Software 7.7.5