Phone Systems

Previous Thread
Next Thread
Print Thread
Rate Thread
Joined: Jan 2005
Posts: 15,281
Likes: 3
Moderator-Vertical, Vodavi, 1A2, Outside Wire
*****
OP Online Content
Moderator-Vertical, Vodavi, 1A2, Outside Wire
*****
Joined: Jan 2005
Posts: 15,281
Likes: 3
A customer has requested if we can block a specific 10-digit number from being able to call in over their PRI. I know I can block them outgoing via COS/TRS, but I've never been asked about inbound. Is this even possible?


Ed Vaughn, MBSWWYPBX
EMP & Lightning Home Surge Protection
EMP - Click Here!
Joined: Mar 2018
Posts: 337
Likes: 1
Member
Offline
Member
Joined: Mar 2018
Posts: 337
Likes: 1
On the 600 can you do inbound call routing based on caller ID numbers? I am pretty sure that you could do it in the voicemail, and then just route the number to a busy signal.


The Cloud is just someone else's computer!
Joined: Jan 2005
Posts: 15,281
Likes: 3
Moderator-Vertical, Vodavi, 1A2, Outside Wire
*****
OP Online Content
Moderator-Vertical, Vodavi, 1A2, Outside Wire
*****
Joined: Jan 2005
Posts: 15,281
Likes: 3
That's what I'm hoping to do. I just don't know where that routing is located in programming. I know I can route DID numbers anywhere I want, but never messed with the actual inbound number itself.


Ed Vaughn, MBSWWYPBX
Joined: Oct 2008
Posts: 297
Member
Offline
Member
Joined: Oct 2008
Posts: 297
It can be done, I just can't remember exactly how at the moment.

I know you have to enable to CLI Ring for the four modes in your DID table. I can't remember for the life of me where to enter the incoming number and the destination.

I had to do it for a nursing home where one resident was calling another ALL day (external call to the other residents DID). I routed the calls out to the Telco test tone.

Joined: Oct 2007
Posts: 294
C5Z Offline
Member
Offline
Member
Joined: Oct 2007
Posts: 294
Yes, enable CLI ring in the DIDs, then assign the callers number into the speed dial table. To the right of the speed dial number in the column for CLI destination, send the call to an analog or PS extension. From there you can forward to a custom greeting" The number you have dialed is not in service"
Kevin


Instructions are just one man's opinion on paper

Moderated by  Carl Navarro, OBT 

Link Copied to Clipboard
Most Recent 5 Post
2nd Call Beep
by MooreTel - 01/27/21 12:58 AM
Summit 800 (9224 Phones) Solid Hold Light
by Keith Janssen - 01/25/21 09:42 PM
Outgoing ANI
by Andyreed - 01/24/21 02:52 PM
Fiber Equipment Installation
by dexman - 01/22/21 11:10 PM
8300 with UCB voicemail to email issue
by Rob Jordan - 01/22/21 06:45 PM
Who's Online Now
32 members (Noobed2336, Meyery2k, nortelvoip, Mercenary Roadie, hbiss, EV607797, ffej010, Professor Shadow, Telephonemaven, royb, dexman, jkmartin, Yoda, RATHER BE FISHING, nabulsi, MooreTel, mc601, BobRobert, KRRath, metelcom, JBean3329, hitechcomm, Curlycord, Touch Tone Tommy, bttirc, Coral Tech, nonameyet, Silversam, hlwilliams, nfcphoneman, Avidcomm, Bob3470), 499 guests, and 48 robots.
Key: Admin, Global Mod, Mod
Popular Topics (Views)
Forum Statistics
Forums94
Topics94,197
Posts638,634
Members49,403
Most Online5,661
May 23rd, 2018
Today's Birthdays
jmd2009, Ken Stephens, Teri J
Newest Members
AleGor, Schreiber, RotoTech99, corkie, FixYaBrokeStuff
49,402 Registered Users
Get Tech Support Now! Click the banner below
Get Tech Support Now!
Top Posters (30 Days)
dexman 33
Yoda 21
Bluewater Sailing
https://www.patreon.com/bePatron?u=5256033
EMP Shield for Commercial - Home & Vehicle
Use Coupon code SAVE - Click Here!
Sold AD
Servpro Ventura 24-Hour Emergency Service
Free Estimates call us now 24Hours
Contact Us | Telephone System Tech Support | Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers.
©Copyright Sundance Communications 1998-2021
Trusted Partners