web statisticsweb stats

Business Phone Systems

Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 2 1 2
#75714 07/28/05 06:34 PM
Joined: Mar 2005
Posts: 14
Member
Member
Offline
Joined: Mar 2005
Posts: 14
I set up a Merlin Legend system for a friend of mine. It's set up in Key mode. My problem is that I can not get the outcalling to work. All the examples show using a hybrid/pbx system using 9* to grab an outside line. How can I grab one of the 4 lines while the system is in key mode.

Thanks.

Avaya IP Office Help & Support Website
IP Office Help

Avaya IP Office Help & Support Website


FAQs, documentation, videos, updates, and support for the Avaya IP Office business phone system!
Everything you need to know about installing, upgrading, and troubleshooting IP 500v2 and IPO Server Edition systems.

Joined: Mar 2001
Posts: 7,350
RIP Admin
*****
RIP Admin
*****
Offline
Joined: Mar 2001
Posts: 7,350
You would still use the 9 *, have given that person the right class of service to allow outcalling?


Russ runs a local service and private tech center.

[Linked Image from sundance-communications.com][/url]
Joined: Mar 2005
Posts: 14
Member
Member
Offline
Joined: Mar 2005
Posts: 14
I checked the class of service (10) so that should be ok. Outcalling is on, But it's not calling out. Is there a setting in the legend that need to be turned on? I read on another site the following (haven't tried it yet):

.............
Can you set-up outcalling on a Merlin Legend Mail/Merlin Legend R7.0 when the system is Key. I think it has to be set-up as PBX/Hybrid, but couldn't remember. Any help would be appreciated

you can. If I remember, you have to assign the lines to the voice mail ports, turn off the ringing, then when it dials 9, it will grab a line.

Thanks ghostinzman, that was the piece I was missing.
..............

I have a 007 (6port) board split in two, 3 ports for AA(group 770) and 3 ports for VM(group 780). (Probaly not the best way to do it, but I have delayed call handling on the AA lines.)

Group 770 has group cover 30 and lines 801 802 803 804

Group 780 has group cover 30 and no lines.

Question, should I have the incoming line in group 780 also?

Thanks
Norm


[This message has been edited by Normand Daoust (edited July 30, 2005).]

Joined: Jul 2001
Posts: 3,347
Likes: 10
Moderator-Avaya-Lucent, Antique Tele
*****
Moderator-Avaya-Lucent, Antique Tele
*****
Joined: Jul 2001
Posts: 3,347
Likes: 10
You're also going to need to have the lines assigned to the last VM port, with ALS set for Intercom, Line 801, 802, etc. Check the restriction level as well, as it will automatically become outward restricted when put into an Integrated VMI hunt group.

Joined: Jun 2001
Posts: 10,949
Moderator-Avaya
*****
Moderator-Avaya
*****
Joined: Jun 2001
Posts: 10,949
I am pretty certain you can't use outcalling on a Merlin in key mode.


Avaya SMB Authorized Business Partner. ACIS/APSS
ESI Certified Reseller/Installer
www.regal-comm.com
Joined: Mar 2005
Posts: 14
Member
Member
Offline
Joined: Mar 2005
Posts: 14
I'm going to do some experimenting this weekend with what I found out. I will post my findings.
Thanks for the info and help.

Joined: Mar 2002
Posts: 3,630
Moderator-Avaya, Nortel
Moderator-Avaya, Nortel
Joined: Mar 2002
Posts: 3,630
Like TTT said, make sure the lines are assigned to the last port. In Key Mode, single line phones & VM extensions can only dial an outside line if the actual lines are programmed to that extension. Turn off ringing, assign ALS to intercom, and make sure you put a 9 in the outcalling number. By default, the vm ports are restricted from outcalling, so you need to enable that as well.


Z-man
Avaya SME Authorized Partner
www.omniofficetech.com
Joined: Jul 2005
Posts: 38
Member
Member
Offline
Joined: Jul 2005
Posts: 38
Would the above steps be about the same on a Magix with Merlin Messaging? (w/PRI)

TIA!

Joined: Apr 2004
Posts: 4,991
Member
*****
Member
*****
Joined: Apr 2004
Posts: 4,991
Norman
did you get the out dialing to work ?

[This message has been edited by KENB (edited August 19, 2005).]

Joined: Mar 2005
Posts: 14
Member
Member
Offline
Joined: Mar 2005
Posts: 14
Ken,
I haven't tried it yet. I have been busy with other projects, and this one currently doesn't have a high priority. I am going on vacation next week, so it's going to be a minium of 2 week before I give it a try. I will post my finding asap.

Norm

Page 1 of 2 1 2

Link Copied to Clipboard
Newest Topics
Inter-tel Encore CX aka Mitel 3000 circa 2008
by Telesystems - 04/27/25 02:20 PM
Just a little of what I've been working on
by John807 - 04/25/25 11:42 AM
Vertical sbx
by Gary S. - 04/25/25 09:59 AM
NEC SV9100 trunk to trunk routing
by utec - 04/21/25 04:23 PM
Forum Statistics
Forums84
Topics94,521
Posts639,995
Members49,851
Most Online5,661
May 23rd, 2018
Newest Members
ferhat_efe, utec, MoverDub, Kevin usama, Pruitt roger
49,850 Registered Users
Top Posters(30 Days)
Toner 8
Taddeo 6
Who's Online Now
1 members (justbill), 239 guests, and 41 robots.
Key: Admin, Global Mod, Mod
Contact Us | Sponsored by Atcom: One of the best VoIP Phone Canada Suppliers for your business telephone system!| Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers. Sundance Phone System Forums - VOIP & Cloud Phone Help
©Copyright Sundance Communications 1998 - 2025
Powered by UBB.threads™ PHP Forum Software 8.0.0