web statisticsweb stats

Business Phone Systems

Previous Thread
Next Thread
Print Thread
Rate Thread
Joined: Jun 2011
Posts: 30
Member
OP Offline
Member
Joined: Jun 2011
Posts: 30
I need to connect multiple systems to a PRI.

Mainly to learn these archaic machines on a live PRI that we support, without having to get another PRI.

Can I plug a hub into it to multiplex the connection? Or would it pass data but not voltage?

Atcom VoIP Phones
VoIP Demo

Best VoIP Phones Canada


Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.

Joined: Aug 2009
Posts: 7
Member
Offline
Member
Joined: Aug 2009
Posts: 7
Short answer: NO. A PRI can only have one endpoint.

Joined: May 2007
Posts: 5,058
Likes: 5
Moderator-1A2, Cabling
*****
Offline
Moderator-1A2, Cabling
*****
Joined: May 2007
Posts: 5,058
Likes: 5
Connect the PRI to one of the systems and then pass the (appropriate) calls to the other PBX(s) with Tie Trunks. This is called Networking. Or at least it was until the IT weenies co-opted the term.

Sam


"Where are we going and why are we in this hand basket?"
Joined: Jan 2005
Posts: 15,378
Likes: 13
Moderator-Vertical, Vodavi, 1A2, Outside Wire
*****
Offline
Moderator-Vertical, Vodavi, 1A2, Outside Wire
*****
Joined: Jan 2005
Posts: 15,378
Likes: 13
Actually, I seem to recall seeing a nice gadget from Adtran that allowed a single PRI to enter it and multiple PRIs came out. Of course, they are fractional, so B1-6 + D appears on the first one; B7-12 + D appears on the second one, etc.

We had one of these for a customer who was using some channels for voice and some for their fax server. It has been about ten years though, so I'm not sure if they are still available.

I'd check with Adtran to see.


Ed Vaughn, MBSWWYPBX
Joined: Jan 2008
Posts: 32
Member
Offline
Member
Joined: Jan 2008
Posts: 32
Take a look at the adtran atlas 550 link below. Lets you plugin the pri from the carrier in and lets you set up other pri's out to differnt pbx's ect. you can route based on did ect. I've used these for years work like a charm. Best part of it all they are fairly inexpensive.


https://www.adtran.com/web/page/portal/Adtran/group/42


Race Communications | http://www.race.com
Joined: Jun 2011
Posts: 30
Member
OP Offline
Member
Joined: Jun 2011
Posts: 30
I have an Adtran 602 total access that a deltacom technician junked. Would that work? It is an IAD. I'm not sure I can factory reset it, but the manual says the craft port provides maximum rights :bang: )

Joined: Aug 2009
Posts: 7
Member
Offline
Member
Joined: Aug 2009
Posts: 7
In its standard form a PRI from the Telco has 23 channels that can be used for voice, "B" channels, and 1 "D" channel. The D channel carries all the signalling and supervision for all voice channels. The Telco PRI can only interface to one endpoint. You would need a box as mentioned above that terminates the PRI and generates separate B and D channels to each output. You cannot do that with a hub or by splitting out wires.

Joined: Mar 2008
Posts: 54
Member
Offline
Member
Joined: Mar 2008
Posts: 54
I'll put in a 2nd vote for an Atlas 550. It can do exactly what you are asking. The units are so versatile that Cisco certification courses use them to simulate the CO in labs.

Get an Atlas 550 with a single T1 card. Add a 1200314L2 dual T1 card and you will be set to go. You might even want to spring for an Octal T1 card if you have several machines that you want live at the same time. You can also get an FXS card and connect analog equipment as well.

Joined: Mar 2005
Posts: 588
Moderator-Mobil Phones, Computers
Offline
Moderator-Mobil Phones, Computers
Joined: Mar 2005
Posts: 588
The 602 is a standard CSU/DSU and won't split out a T1 but the 550 that's been recommended will. One good thing about Adtran is they offer excellent support. Give them a call and discuss your situation and they will recommend the best option.

Joined: Sep 2006
Posts: 3,290
Member
*****
Offline
Member
*****
Joined: Sep 2006
Posts: 3,290
The Adtran 750, if equipped with a List 2 BCU will allow "drop/add" (you can Google that term and find out a lot about how it's done and who does it).

You derive a second T1 connection from the 1st channel bank that runs via a 4-wire ckt to the 2nd channel bank.

The channel bank has two 8p8c jacks. One is IN and the other is OUT, basically.


Arthur P. Bloom
"30 years of faithful service...15 years on hold"


Moderated by  Silversam 

Link Copied to Clipboard
Forum Statistics
Forums84
Topics94,283
Posts638,765
Members49,764
Most Online5,661
May 23rd, 2018
Popular Topics(Views)
211,446 Shoretel
188,305 CTX100 install
187,082 1a2 system
Newest Members
Nadisale, andreww, gohunt, Darrick, telecopippo
49,764 Registered Users
Top Posters(30 Days)
Toner 23
teleco 7
dexman 4
jc2it 4
Who's Online Now
2 members (aweaver, Professor Shadow), 165 guests, and 286 robots.
Key: Admin, Global Mod, Mod
Contact Us | Sponsored by Atcom: One of the best VoIP Phone Canada Suppliers for your business telephone system!| Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers. Sundance Phone System Forums - VOIP & Cloud Phone Help
©Copyright Sundance Communications 1998-2024
Powered by UBB.threads™ PHP Forum Software 7.7.5